- $6000 on dust collection, give up woodworking or guaranteed health issues?
- Are Room / shed filters worth the money
- 6" Fittings
- Anyone interested in a Hafco cyclone ?
- Dusty mod - building the adapter flange
- 3hp dusty solution
- Which to buy for modifing?
- Are manufacturers stupid.
- Powtran VFD Help Required
- Dust hood for Harvey table saw.
- Do I need bag/filter with a cyclone?
- 2 small dusty or 1 large dusty
- Dust Cupboard design
- Ducting a shop vac - potential problems?
- Some Questions re Clearvue Cyclones
- Bandsaw Dust Extraction with Clearvue
- a new take on dust extraction
- Metal dust catcher
- More bandsaw dust extraction ideas.
- Cabinet Dust Extraction On a Hammer Slider
- Dust from a dusty
- Speedlock ducting - anyone used?
- Help with Shop Vac selection.
- Dust Extraction
- Sensitive vacuum switch for DC ducting.
- Router table - under table extraction
- Just how big is 6" duct? --> HUGE!!!!
- pipe up dust collection
- Machinery Warehouse DC-7
- Wanted 2 bag dust extractor
- Replacement Dust Bags
- Festool Kapex SCMS dust hood.
- 2 HP dust collector upgrade
- How to get impellor off motor shaft
- muffler location in dusty enclosure
- 6" ducting plan
- Clearvue 16" Impeller
- Best dust extraction for Carbatec thicknesser
- Separating motor and impellor from the filter unit
- Bell Mouth in PVC
- Spindle sander dust collection.
- Room Dust Filters - need a diffuser?
- Where to start?
- PCV pipe and flexible duct size
- DE for a kinda small shop
- My basic tests with a 2/3 Cyclone @ 3HP
- Installing my Dusty - WIP
- Replace bottom filter bag with a drum?
- Dusty Questions
- FM 300 2hp dusty bag pole
- Getting the shop vac outside.
- Moving the DC outside
- Dust extractor for table saw
- Generic 2hp mods with cyclone
- Single phase to 3 phase through Powtran VFD
- $25 Cyclone - taking a risk.
- 15.7" impeller on a 2HP dusty - a good thing?
- Anyone need a dust extractor?
- opinions wanted on router dust collection
- Multi tester for the shop?
- Yet another "Is DC right for me" thread
- mobile dust extraction for drop saw & other tools
- Do I need shielded cable when connecting a Powtran PI8100
- Bell mouth hood offer - expressions of interest
- sealing DC enclosure doors
- Cleaning pleated filters
- Planning my ductwork / DC / machine layout in new workshop
- Blast gate gallery
- Floor pick up
- Too much vacuum
- Extraction Outlet size?
- Clearing the air
- 3 hp DC
- Airtight joint?
- My dust extraction journey begins here.
- Shop vacs which don't cost the earth?
- Rigid pipe for dust collector
- Felder AF 12 | Ø 120 mm
- Flexible ducting advice
- A 3HP (15A rated) DC in a shed
- Dust Extraction Experiment
- Cabinet for Makita scms
- Wanting to buy a 2hp dust extractor
- Anybody got one of these vacuum heads?
- The scary result of ZERO dust extraction in a cabinet.
- Overhead TS Dust Extraction Hood
- Quick and dirty Blast Gate.
- Fitting out a new (small) shed.
- DC-7 3HP Mods
- Air flow calibration measurements
- Hand held router dust extractor box type thingo WIP
- Bill Pentz's Design: Lengthening Outlet Query
- Mounting motor upside down and to the side (Plenum)
- Small workshop added DC ducting and layout.
- A good reason to put a DC outside a shed
- Dust extractor emergency stop switch removal
- Laguna cyclone
- Record Power DX4000 Vacuum
- Connecting impellers to systems
- Dust Extraction for Hand Held Power Tools
- Let's see what we can do.....
- Oneida Supplier in Aus?
- Are the PVC users here not earthing any more?
- Developments in Dust Sensor tech
- spindle sander dust extraction
- Dust Collection while sanding - an interesting product
- Fitting pleated cartridge
- Converting drum sander to 4" outlet.
- Dust Collection Install - WIP
- Dust/chip extraction for occasional work
- Some advice appreciated for small garage hobby shop
- Cyclone separator into open bag, no filters on external exhaust.
- dust extractor vacuum pressure generated at nominal velocity
- Improving fan performance
- Air purifiers for the home
- Oneida Super Dusty Deputy 4" Group Buy
- $40 3PH dusty in Victoria on Gumtree
- Wok is the wok for? - dust extractors
- Hafco W318 dust extractor.
- Purchasing/Setting up New DC System - Advice
- Toying with extraction layout
- "Saw dust bin full" Sensor
- Fire in the hole
- Solder fume extraction.
- Help Needed for new workshop
- Timecon DC-1750. A question on design and a deficiency?
- Making sure your DC is on
- Questions about a second hand set up.
- Pleated Filters - what are the best? Is there a "best"?
- Does a wok rock or not
- Wood smell in workshop?
- Single Car Garage in a Townhouse - DC Thoughts
- Dusty install - outlet questions
- Dust/shaving galore
- Two dust extractors in parallel
- Clearvue Oz - not able to contact
- Clearvue Max Amps?
- Does a 2hp dusty have to be perfectly vertical?
- Sherwood FM400 3hp extractor
- Replacing dust bag with drum
- Sawstop - Festool Overhead Dust Collection
- Flexy ducting
- Love some feedback on prelim dust extraction plan
- Dust collector is like a child…
- meaningless manufacturer specifications
- 100mm Suction hose
- Dust extraction in a cold climate
- Any practical use for a 1hp blower?
- Sanding Room
- Dust Concentration Measurements