- Some Advice: Slitting cutter on a HM-46 Vertical Mill.
- Mahr depth micrometer
- Dividing plate for 127 divisions
- Surface grinding & beer
- Request for Melbourne members
- Anti Pullout Fixing - An Idea Maybe?
- T-Slot nuts for Hercus milling attachment
- Thread inserts
- File sizes?
- HM 46 milling machine single phase or three phase
- Singer 29K13 restoration article
- Machine freight Adelaide to Sydney - advice please
- VFD and 3 phase conversion of my 45 size gear head mill
- Autocollimator's and alignment Telescopescopes
- Treasures from the shed pt II
- Remington Promotional Movie from 1969 on YouTube
- Case Hardening Steel
- Lifting surface grinder ????????
- Old Information on Industry and Manufacturing in England
- Swiss Captivity
- Metal Band saw
- MT4 draw bar
- flanged (collar) nuts
- Shaper idea
- Attach awning brackets to a Steel Hollow Section
- Oil Blackening Steel
- Question about the small VSD's
- Gedore 80mm Ratchet Ring Spanner
- Shaper ATLAS
- How would you make this?
- Check out the size of this vernier ....
- vibration during turning
- What Diameter for threaded rods/shafts etc
- Offcuts in Melbourne?
- glass drilling
- Day two at Lake Goldsmith
- Globe Drill Press
- Scraping
- Shock, horror, gasp, lathe bed rust!
- socket head screw sets? Where for decent price?
- Cincinnati pedal power
- Tailstock Alignment Using Test Bar- A Youtube Clip
- Tool bit storage tubes
- Slitting saw bore sizes
- Milling Cutter Choices
- Double 45deg bends in an aluminium flat bar...??
- Rubber Linisher Wheel
- Mahr dial gauge query
- Drilling a hardened steel vice
- Bandsaw blades
- Which 8 inch Rotary Table to Buy?
- DIY magnetic swarf wand
- Paring with the lathe. (not parting)
- mystery metal
- Book query 'The Amateurs Workshop'
- Link to metalwork news
- Thermal shrink fit
- Welded a square tube box, which torsional brace?
- A Catch Plate Fly Cutter
- 5/16 Brass
- Rf 40 cum mill advice again please
- Milling machine way bellows
- Key Removal
- Anyone dabble in metal spinnng? Small (and I mean small) job.
- Well, that went well, not!
- Help - Need to find tapered drift (Lathe helper?)
- Advice needed
- Asset sale flyer
- How big a hammer do you need?
- Wing Industries
- Couple of ideas
- Hamatu Lathe
- Mitutoyo's Uni-Mike
- Another Mag transfer block
- Superglue and Washer Turning
- hafco tc 450 tool and cutter grinders
- 82 and 90 degree countersinks
- sheet metal work
- Headstock alignment
- Do you know
- what does this do?
- Small tube bender?
- Newby
- Bottoming/Plug Taps
- Smallish lathe commission? what can i expect to pay?
- harrison lathe
- Victoria Dividing Head(40:1) Manual
- Steelmaster 1022 v 0920A lathe
- Hello
- Mounting chuck on 6" Vertex RT
- $80 lathe
- Getting objective in the shed
- What kind of tool could be used to do this?
- train video
- Hafco AL-336 Imperial Thread
- Engineers Vice Issue
- HM-48 DRO issue.
- cheap lathe suggestions ?
- vernier query
- Tough drill press
- Lathe painting question
- Putting my optical comparator to work.
- Machining morse tapers ( internal)
- On the LEVEL.
- SHW Mill
- Interesting Gauge stand
- How To Avoid Cross Threading Bolts and Screws
- Mazak Quickturn training, Where?
- Tool Chest
- suitable surplus source for right angle worm drive gear box ?- power hacksaw
- Sheraton Conquest Head Gear
- lathe coolant
- How To Drill Accurately Located Holes in Inside Radius of Angle Iron?
- removing ball bearings from their races
- C.C. tool and cutter grinder restoration
- Rivets
- Dial test indicator suppliers?
- 1942 film
- Was this just good luck?
- Lever locking pliers - slide hammer adapter
- Drilling Hard or Case Hardened teel
- Extension of Experiments in Machineable Wax
- Slitting Saw Holders
- eBay- how long is too long to wait?
- Ball Turning Tool
- Welders
- Where to buy very thin sheet steel
- Magmaweld Low Hydrogen Rods - Melbourne Supplier ??
- Big machine guard made.
- Need help to make replacement part for drill press
- 416 Stainless
- What grease for brass and plastic?
- Shaper basics
- But there's no catch...
- Graduated Adjustment Dials
- Getting mill into workshop
- Setting up a New Mill
- Hercus power hacksaw attachment!
- Busted my pedestal drill
- Need help identifying the electric motor!
- Mazak course in Perth, looking for people
- Dial vernier calipers ?
- Need the right name for a gizmo.
- copper sheet
- Enco discount code
- Search engine
- power feed on mill/drill
- Considerations making an RF45 drawbar
- Timken badge
- Gauge blocks