wally peat
23rd June 2009, 03:01 PM
OK, with apologies to Ern and all those who wanted to know what he did with his big black beast, it's been at my place for a week, and I've finally managed to make the planets align sufficiently to post a photo here as proof. (I just hope it's small enough to be allowed on the forum).
By way of introduction as to why I'd buy a machine like this, I could explain how I picked up an mc900 from a school clearout some time ago, liked turning and thought one day when I could afford it I'd buy a real lathe, but I'm sure you can see through that and all recognise a tool s**t when you see one. :o
I reckon Ern's machine was a bargain, I was lucky with the freight and unless it's been badly abused, the work it has already done has barely run it in. Should still be turning things when I've done turning in my grave.
I'm a keen woodworker, and if you want to know my preferences in woodwork, check out my avatar. Unfortunately you can only keep so many boats in the yard, so diversify it is. I have pretty much everything to learn about turning, but I went to a class and really enjoyed using a skew, so I figure the rest of the journey can only get better.
That means I won't be taking up with the Stubby where Ern left off, probably more like I'll be somewhere the other side of where he started, but there's some good woodturners in Townsville, and so far they've been free with their advice and support.
If any of you forumites are in the area and want to come and have a turn, just pm me and we'll arrange a time. Hopefully I'll learn something too.
Just one other thing to gloat about... The same time the stubby arrived, someone I know cut down a substantial mango tree, and the best bits were kept out of the chipper. This weekend one of those generous local turners showed me how to slab it with the chainsaw, and I was stunned to find a glorious fiddleback grain right through the centre of the slab. You will see from the second photo, that the slab is sitting on the same pallet that delivered the Stubby to my place, so it's just as well I've found a lathe with the capacity to turn something big - the fiddleback goes right out to the sides.
Hopefully I'll make something worth photographing to post here, but I would like to say thanks to everyone who contributes to this forum for all the things I've learnt already, and a very special big shout to Ern, who delivered everything he promised, and all packed with the care and attention he obviously takes with his woodturning.
Gotta go, something's calling me from the shed :D
By way of introduction as to why I'd buy a machine like this, I could explain how I picked up an mc900 from a school clearout some time ago, liked turning and thought one day when I could afford it I'd buy a real lathe, but I'm sure you can see through that and all recognise a tool s**t when you see one. :o
I reckon Ern's machine was a bargain, I was lucky with the freight and unless it's been badly abused, the work it has already done has barely run it in. Should still be turning things when I've done turning in my grave.
I'm a keen woodworker, and if you want to know my preferences in woodwork, check out my avatar. Unfortunately you can only keep so many boats in the yard, so diversify it is. I have pretty much everything to learn about turning, but I went to a class and really enjoyed using a skew, so I figure the rest of the journey can only get better.
That means I won't be taking up with the Stubby where Ern left off, probably more like I'll be somewhere the other side of where he started, but there's some good woodturners in Townsville, and so far they've been free with their advice and support.
If any of you forumites are in the area and want to come and have a turn, just pm me and we'll arrange a time. Hopefully I'll learn something too.
Just one other thing to gloat about... The same time the stubby arrived, someone I know cut down a substantial mango tree, and the best bits were kept out of the chipper. This weekend one of those generous local turners showed me how to slab it with the chainsaw, and I was stunned to find a glorious fiddleback grain right through the centre of the slab. You will see from the second photo, that the slab is sitting on the same pallet that delivered the Stubby to my place, so it's just as well I've found a lathe with the capacity to turn something big - the fiddleback goes right out to the sides.
Hopefully I'll make something worth photographing to post here, but I would like to say thanks to everyone who contributes to this forum for all the things I've learnt already, and a very special big shout to Ern, who delivered everything he promised, and all packed with the care and attention he obviously takes with his woodturning.
Gotta go, something's calling me from the shed :D