Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Dremel powercarving speeds
-
14th February 2008, 08:32 PM #1
Dremel powercarving speeds
I have just bought the domestic engineer a wecheer reciprocating flexishaft for her dremel. What I am after is does anyone know what speeds to operate this with?... At the start silky oak will be used.... untill the offcuts run out...
jenno
-
14th February 2008 08:32 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th February 2008, 09:05 PM #2
Hi jenno
I haven't got the flexishaft but I have a dremel. All I can suggest is to experiment with a bit of scrap wood first. They are realtively safe machines to use depending on what tool bit you use, the dangerous ones are those that have a circular cutting wheel With the grinding or sanding type tool bits, if your careless you might remove a bit of surface skin but the worst that will do is is remind you to concentrate on the job at hand. Be careful not to where loose clothing or work too close to the rest of your body and where protective eyewear. Also the faster the speed the greater the chance of burning the wood.
-
15th February 2008, 07:39 AM #3
It really depends on the shape and cut of the cutter.
You need to experiment with the speeds on different timbers.
Too slow and they will bounce and too fast they will burn, you just have to find the middle ground.Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
15th February 2008, 09:02 AM #4
the thing diffrent with useing the flexishaft is if you can hang the dremel over your right shoulder this will keep the shaft running better and what springwater said
smile and the world will smile with you
-
15th February 2008, 01:50 PM #5
with variable speed tools, I usually wind them up till
something breaks, then back them off about a 1/4 turn.
that was no real help at all was it?
best follow the others advice
one suggestion though, when you run out of siky oak
stay with woods that are equally as friendly,
some of these reciprocating carvers weren't designed with
Australian hardwoods in mind.
-
15th February 2008, 04:32 PM #6
cheers all....will keep these things in mind
jenno
-
15th February 2008, 08:53 PM #7
[quote=one suggestion though, when you run out of siky oak
stay with woods that are equally as friendly,
some of these reciprocating carvers weren't designed with
Australian hardwoods in mind.[/quote]
99.9% of tools aren't designed to cope with Australian Hardwoods!
-
16th February 2008, 08:28 AM #8Senior Member
- Join Date
- Jul 2007
- Location
- Loire , France
- Posts
- 349
Guess they weren't designed with any hardwood in mind...I had a AEG carver when I started, and tried it on olive root...then I sold it and started investing in gouges and chisels instead, the best thing I ever did!At times, when I have to use some heavy- duty tools, the kind you hit with the malet as it were your mother-in-low's thumb, ahd splinters the size of banana fly all over the workshop, that ridiculous toy comes to my mind...
It's a slow and painful process...the secret is, dont mind the pain.(Ian Norbury)
________________________
Regards
Ivan Chonov
-
16th February 2008, 11:54 AM #9Intermediate Member
- Join Date
- Dec 2006
- Location
- Los Angeles, CA, USA
- Posts
- 48
I don't remember where, but I recall seeing a mfgr's
reccomendation that rpm's not exceed 5k when using recip hand piece.
AKA "The human termite"
Similar Threads
-
Arbortech powercarving stuff for sale
By scooter in forum WOODCARVING AND SCULPTUREReplies: 0Last Post: 22nd October 2007, 05:05 PM -
Powercarving question
By Luxyboy in forum HAND TOOLS - POWEREDReplies: 16Last Post: 28th September 2007, 07:04 PM -
Speeds
By mjford in forum WOODWORK - GENERALReplies: 5Last Post: 24th May 2005, 11:57 AM