Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: help for newbie
-
17th January 2018, 08:11 AM #1New Member
- Join Date
- Jan 2018
- Location
- Gold Coast Australia
- Age
- 70
- Posts
- 2
help for newbie
Hi i have just started to do some hand carving. I have done a couple of birds in Balsa as a learning exercise. I would really like to get some advice on what is the best and easiest wood to use and where this can be sourced (I live on the Gold Coast). At this stage I am just looking to do small projects e.g. small models, spoons, knives etc. Any help advice would be greatly appreciated.
Thanks Alan
-
17th January 2018 08:11 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
17th January 2018, 11:39 AM #2
Balsa is a terrible wood to carve - way to soft and "squishy". The fibers will crush instead of being cut. One of the good carving woods where you are is jelutong for figure carving. For spoons or other cooking utensils, a deciduous wood would be best. Here in the US, that would be birch, maple, walnut, cherry or other fruitwood, poplar, etc. Oak is usually too porous, and conifers are often resinous or have pronounced hard/soft/hard/soft grain structure.
Jelutong | The Wood Database - Lumber Identification (Hardwood)
I also found this reference that might help you: https://www.daf.qld.gov.au/forestry/...f-timber-trees
Claude
-
17th January 2018, 01:00 PM #3GOLD MEMBER
- Join Date
- May 2013
- Location
- Rockhampton QLD
- Age
- 68
- Posts
- 2,343
Welcome to the forum Alan.
-
17th January 2018, 11:53 PM #4SENIOR MEMBER
- Join Date
- Mar 2014
- Location
- UK
- Posts
- 349
Well I'm in the UK so wood alternatives are different but definitely not balsa !
you can get Obeche I believe that is soft & well behaved if a bit boring.
Mike
-
18th January 2018, 11:08 AM #5Member
- Join Date
- Jun 2012
- Location
- Diamond Creek, Vic
- Posts
- 84
I found that Queensland White Beech and Camphor Laurel carve quite well. The colour in Camphor might interfere with your designs, so look for fairly plain pieces. You should find both species in your neck of the woods. Huon Pine and Lime or Bass wood are also good choices if you can find them. Lime from Europe Bass from US are the same tree. Most fruit wood, like pear and nut woods also carve well but can be a bit hard but take good detail. Kauri pine is also suitable if it is not too soft. The hardness can vary depending where it comes from.
-
18th January 2018, 05:49 PM #6Senior Member
- Join Date
- Mar 2012
- Location
- Perth
- Posts
- 470
Hi I agree with Blackforester on the woods to carve, white beech, huon pine and Camphor laurel are great woods to carve, I don't think you'll find any Jelutong around now unless your lucky and get some old stock, it's been banned in Australia
so I'm told by a few suppliers. Western red cedar is not bad to carve and English lime if you can find it. Good luck.
-
20th January 2018, 07:10 PM #7
G'day Alan
and welcome to the forum, as a possible source for jelutong, check to see if you can locate any Pattern makers nearby, they use it a lot and may sell you some of their scraps and off-cuts
I have no problems getting Jelutong, and for special projects I go to a furniture making company and they order in what I want.
Regards
John
-
25th January 2018, 04:39 PM #8Senior Member
- Join Date
- Jul 2008
- Location
- Sydney
- Posts
- 299
Hi Alan, I agree with the previous three comments. Although I haven't heard of jelutong being banned in Oz; maybe that's because there's still plenty around at the wood specialists. You may be able to get Qld Cheesewood, which is Aussie grown jelutong. Always good to support the local growers.
Also, give camphor laurel a go, sometimes the patterning in the wood works with your design .
Good luck, Peter
-
27th January 2018, 12:55 PM #9New Member
- Join Date
- Jan 2018
- Location
- Gold Coast Australia
- Age
- 70
- Posts
- 2
Hi thanks to all respondents.
I have managed to discover that my Brother-in-law has some Huon Pine and is going to send some to me. What and how much I get will be a surprise when the parcel arrives.
I agree about balsa but it is giving me some good experience - the "squishiness" is a problem - with a bit of sanding I can much reduce the effect.
Alan
Similar Threads
-
Another Newbie
By robba74 in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 5Last Post: 3rd February 2012, 07:55 PM -
Newbie
By GidgeeCube13 in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 8Last Post: 2nd February 2012, 08:42 AM -
Another Newbie
By Rocketz in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 3Last Post: 19th May 2011, 08:06 PM -
newbie's first box here
By Alex07 in forum BOX MAKINGReplies: 10Last Post: 12th September 2007, 11:42 AM