Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
27th November 2010, 10:46 PM #1New Member
- Join Date
- Nov 2010
- Location
- kingsgrove,sydney nsw
- Posts
- 7
aluminium windows & their flashing
hi guys,i have a three bedroom home thats approx. 60 yrs old. ive recently done some extensive renovations, including replacing the old worout timber windows for new aluminium ones, id like to know where the flashing sits, now the hose is double brick, and the new windows are fitted with timber reveals, also the house is going to be rendered, the qwestion is dose the flashing hang in the brick cavity, or dose it sit ontop of the brick sill,and then redered on top.?
-
27th November 2010 10:46 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th November 2010, 08:56 AM #2Member
- Join Date
- May 2009
- Location
- Sydney Australia
- Age
- 70
- Posts
- 67
The flashing is laid under the brick sill on the outside skin. A couple of weep holes wouldn't go astray as well.
I'm not young enough to know it all.
-
28th November 2010, 12:01 PM #3GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
If you are referring to the rubber flashing at the bottom of the window ,Mojoe, then this must finish sitting on top of the render so that the water from the glass will finish running off the sill. If the window is in a double storey section of the house then flashing must be installed across the cavity with weep holes in the outside skin and the flashing should extend a bit on either side of the window .
CheersI've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
28th November 2010, 08:20 PM #4New Member
- Join Date
- Nov 2010
- Location
- kingsgrove,sydney nsw
- Posts
- 7
thanks
hi there, peter 36, thanks for the info, yes i figured the rubber seal sits ontop of the render, but the plastic one i wasnt shure of, its only a single story, double brick, im sorry if im replying to you in the wrong section, cos this thing about sending /reciving messages is fairly new to me. Do you think i would have to remove the row of bricks which is the sill, lay the plastic flashing, and then re-lay the sill ontop of the flashing? or if i cut the flashing out alltogether what would be the worst that could happen?
cheers moejoe
-
28th November 2010, 08:27 PM #5New Member
- Join Date
- Nov 2010
- Location
- kingsgrove,sydney nsw
- Posts
- 7
-
28th November 2010, 08:47 PM #6GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
I,m trying to get the correct picture. Does your window have in addition to the rubber flashing, a second plastic flashing which is attached to the bottom of the reveal/window frame ? If this is the case then I would suggest that you could remove the plastic flashing from the window.The plastic flashing is there to capture any water which may enter the cavity between the side of the window and the aluminium frame of the window which is important if the window is installed in a double storey . In your case the render will fill any gaps between the brick and the window , but if you are concerned you could place a bead of sealant there before you render.In Melbourne our Al, windows only come with the rubber flashing and any other flashings which might be required are installed separately.
CheersI've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
28th November 2010, 09:11 PM #7
Mojoe,
you may have more fun over at our sister forum Renovate Forums - Powered by vBulletin.
Lots of tradies with advice over there.
-
29th November 2010, 06:04 PM #8New Member
- Join Date
- Nov 2010
- Location
- kingsgrove,sydney nsw
- Posts
- 7
that makes sense
Thanks for that peter 36, i think your right on the mark, what you've suggested has made the most sense so far, im gunna go with that, thaks mate,,,