Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Cutting Circles
-
16th January 2009, 11:54 AM #1Intermediate Member
- Join Date
- Dec 2008
- Location
- Melbourne
- Posts
- 29
Cutting Circles
Hi Everyone,
I am just seeking some advice for cutting circles. I want to be able to cut two circles out of timber with about a 10cm diameter. I should slo note it is the circles I want and not the holes if that makes sense!! My skills with a jigsaw are poor and I was thinking about trying to make some sort of template to use a router but I am not sure. Could anyone give me some advice on this?
Thanks
Mick
"A zebra does not change its spots" -Al Gore 1992
-
16th January 2009 11:54 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
16th January 2009, 12:11 PM #2
lets start woth what tools do you have on hand, and we could give you some options
I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys
-
16th January 2009, 01:05 PM #3Intermediate Member
- Join Date
- Dec 2008
- Location
- Melbourne
- Posts
- 29
Hi Gra,
Power tool wise I have a router, jigsaw, circular and mitre saw and an electric plane. As far as hand tools go I have a couple of panel saws and some tenon saws, hand planes, chisels etc.
Hope that helps. So far I was thinkin of making some sort of jig or something to spin the router around.
Thanks
Mick
"A zebra does not change its spots" -Al Gore 1992
-
16th January 2009, 01:10 PM #4
From looking at your tools, I would suggest two methods;
1. Router tramel, basically a stick attached to you router base at one end, and a pin in the other end. Pin goes in the middle of your required circle, then rotate router a fixed distance from the pin, repeat until you are all the way through.
2. If you have a table to mount the router in, then affix a pin to the table the radius of the circle you want, and Pin goes in the middle of your required circle, then rotate the stock a fixed distance from the router bit, repeat until you are all the way through.I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys
-
16th January 2009, 01:43 PM #5Golden Member
- Join Date
- Oct 2006
- Location
- Dandenong Ranges
- Age
- 47
- Posts
- 816
Router Trammel might not be practical for a 10cm diameter circle.
You didn't mention if you had a drill but if you're going to buy one, a hole saw bit might be the go. Although it will leave you with a hole right in the middle of your circle.___________________________________________________________
"The things I make may be for others, but how I make them is for me."
-
16th January 2009, 01:47 PM #6I may not have gone where I intended to go, but I think I have ended up where I needed to be.
My Other Toys
-
16th January 2009, 01:49 PM #7
I have a router jig made of metal for cutting circles. I will be doing a review of it soon but essentially it is a simple bar of metal with some bends and attachment points plus some accurately drilled holes. They cost about $30 and are for sale in Williamstown at Get Woodworking (9399-1963). I am not sure if the jig will go down to 10cm.
-
16th January 2009, 04:49 PM #8Intermediate Member
- Join Date
- Dec 2008
- Location
- Melbourne
- Posts
- 29
Thanks for that folks. I am going to get some hole saws this weekend.I'll look into the router jig too.
Thanks again!!!
"A zebra does not change its spots" -Al Gore 1992
-
16th January 2009, 05:13 PM #9SENIOR MEMBER
- Join Date
- Oct 2008
- Location
- Perth
- Posts
- 966
You'd think a circular saw would be good for cutting circles, wouldn't you?
-
16th January 2009, 06:52 PM #10SENIOR MEMBER
- Join Date
- Feb 2007
- Location
- Adelaide
- Posts
- 595
Kahlua, just be careful if you have a disc only 10m diameter on a router table. Your fingers may be too close to the cutter for comfort. If you happened to get the direction of rotation wrong - which is not unimaginable because once I did it - a small workpiece can get snatched and whizzed around with nasty results. I am sure you will be careful near the router cutter, but be absolutely sure of what you are doing. Personally I would avoid getting my fingers too close to something that could get grabbed and pull your fingers round and about.
-
16th January 2009, 08:00 PM #11Intermediate Member
- Join Date
- Dec 2008
- Location
- Melbourne
- Posts
- 29
Thanks fencepost, I'll take it nice and slow so I make sure I don't fall into any traps like that.
Thanks again
"A zebra does not change its spots" -Al Gore 1992
-
18th January 2009, 09:55 AM #12Novice
- Join Date
- May 2008
- Location
- Perth
- Age
- 52
- Posts
- 20
10cm holes with router jig
it is fairly easy to cut 10cm holes (or even smaller ones) using a router trammel. Just make sure the pivot point is sitting underneath your router base plate. Make sure you don't cut through the materail (since you will loose the mounting for the pivot point). Instead go down 2/3 thirds - this will be your guide later to clean up the last 1/3. Then rough cut the 10cm hole with a jig saw or something. Clean up the last 1/3 with a straight router bit that has a guide bearing wheel and follows the first 2/3 that you have routed out cleanly. The guide wheel can either be at top or bottom - you can flick over the material (the clean 2/3 cut is now facing down) if guide bearing is at the tip of router bit.
hope that makes sense ;-) good luck
-
18th January 2009, 10:10 AM #13Senior Member
- Join Date
- Jan 2008
- Location
- qld
- Posts
- 159
A 100mm hole saw will need a fair sore of drill to go through hardwood. If you use a drill press you can remove the centre pilot drill bit once you get a bit of depth Otherwise you can sandwich a scrap piece to your hardwood with a hole already cut in the top (scrap) piece. In both these setups the existing hole will guide the rim on the saw and you don't get a pilot hole on both faces of the circle.
What thickness is the timber, as this may limit your choice of techniques.
Regards,
James
-
19th January 2009, 05:07 AM #14Senior Member
- Join Date
- Sep 2006
- Location
- Bookham, Surrey, UK
- Age
- 79
- Posts
- 137
Here are a couple of trammels, one for cutting small holes and the other for larger ones http://www.wealdentool.com/acatalog/tips_4.html
Hope this helps.
Cheers
Paul
Similar Threads
-
Cutting circles with a router
By felixe in forum ROUTER JIGSReplies: 12Last Post: 19th December 2007, 12:04 PM -
Cutting circles with the router
By BarryBurgess in forum TRITON / GMCReplies: 17Last Post: 25th September 2005, 05:10 AM -
Question on cutting circles
By Wild Dingo in forum WOODWORK - GENERALReplies: 5Last Post: 16th November 2004, 06:02 AM -
Cutting Circles
By minis4meau in forum SCROLLERS FORUMReplies: 0Last Post: 12th January 2004, 09:50 PM -
Circles
By Robert WA in forum HAND TOOLS - POWEREDReplies: 6Last Post: 2nd November 2002, 10:13 PM