Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 32
-
30th October 2009, 11:36 PM #1.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Dominoed wine rack pigeon hole WIP
A small WIP on how I use the Domino to quickly assemble pigeon holes for wine bottles on the side of a buffet.
Pic 1- Shows the layout of the bits and pieces used. (L to R)
Top - Divisions, clamps, Domino with wings and a 5mm cutter, added for spacing.
Bottom - Platform spacer, platform, division, cabinet side.
Pic 2- Shows the division clamped to the side and the Domino resting on top with the registration pin hard up againsed it. Then plunge.
Pic 3 - Shows the pin on the extension wings inserted into the previous mortise for quick accurate spacing.
Pic 4- Shows the platform (same spacing and 5mm Dominos glued in) inserted into the mortises with spacer clamped on, and the previous pic 2 and 3 repeated.
Pic 5- shows the process repeated to the top.
Pic6 - Shows the completed mortises perfectly spaced.
The rest will be posted tomorrow.
-
30th October 2009 11:36 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
31st October 2009, 01:57 AM #2
-
31st October 2009, 07:19 AM #3
Thank you for sharing your technique Lignum, you make it look too easy with the Domino.
Regards
Al .
You don't know, what you don't know, until you know it.
-
31st October 2009, 08:18 AM #4
Good stuff, exactly how i've done it before too, but i lay the piece down flat on the bench and hold the Domino vertically. For your shelves did you hold them down flat, then work off the bottom of the Domino with that flat on the bench too?
Dominoes are good aren't they, i loved how you did your dovetail housings with one in another thread (sure it was you)
Also worth noting that if you've got shelves on the other side of your division that you want in the same positions, then you can plunge straight through the division, then the shelves will line up perfectly.
-
31st October 2009, 08:47 AM #5.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Carp, the reason (for me) its in the upright position, is to make it easy to set the first division plunge and clamp the division on for the next lot. That cabinet side is loose and I will take it off and put the main side on and repeat the process. I will also post the pic of my simple method of getting the position of the angled inside shelf Dominoed in. And yep, the dovetail thing was mine. A bit of fun to show the versatility. I have 2 new spline jigs just about finished and will post in a week or 2
Sheddie, they are around 80 bucks. Their doesn’t seem to be a lot of love around the world (on forums) for them, but I love mine and use them heaps.
-
31st October 2009, 02:39 PM #6
-
31st October 2009, 11:01 PM #7.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Pic 1- Shows the division Dominoed using the same spacing as the side. The 2nd and 3rd spacing are mortised using the 2nd Domino width setting.
Pic 2 - Shows a dry fit to make sure the bottle fits
Pic 3 - Shows some scrap cut to 95mm width to get the correct Domino spacing to hold the bottle in the centre and the middle back one is to stop the bottle sliding back into the cabinet.
Pic 4 - Shows the division being Dominoed. The top was using the fence and the bottom using a spacer.
Pic 5 - Shows a spacer (left) to accurately place the middle back Domino.
Pic 6- Shows the bottle placed in the Domino stops.
-
31st October 2009, 11:30 PM #8.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Pic 1- Shows the divisions being glued to the inner sides. They are just glued and hammered home and not clamped as the Domies are a great fit. I use the square to make sure they are all at 90deg. I leave them flat like that for a few hours to dry.
Pic 2- Shows the inner slides fitted to the base,
Pic 3 and 4- Shows the dry fit up. I still need to add the Domino spacers for the wine bottle on the base…. I forgot about that.
-
1st November 2009, 09:42 AM #9
you are domino crazy.
Since you got it, how many domino's do you think you've been through?I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
1st November 2009, 10:11 AM #10.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Domino crazy’s not the word. Awesome tool when you are trying to pump out moderately cheap work to make a living. With this cabinet, just the two pigeon box ends, sides to base, centre divider (not shown) and edging, there are 129 Dominos. So I couldn’t even begin to estimate 3 and a half years of flat out Dominoing
-
1st November 2009, 10:28 AM #11Senior Member
- Join Date
- Jul 2007
- Location
- Perth
- Age
- 53
- Posts
- 158
What a great idea there,
Really like the use of the domino as a stopper for the base of the wine bottle
-
1st November 2009, 05:10 PM #12
Great work, Lignum. Amazing how much you've been able to get out of your domino.
Just a thought, most people seem to prefer the bottles snuggled into the holder rather than sticking out as in pic 2 on post 7. That may not have been testing the fit of the back stop, in the pic with the back stop it looks a bit deeper. But even if the bottle doesn't stick out at all it's still easy to grab the neck.
Also there are a number of odd shaped bottles out there. Might be a good ideal to get hold of a Peter Lehmann, Rockford, and a Moet to make sure they all fit. Plus you should be able to write off those purchases as a business expense
My domino came with the wing, and I haven't figured out what it's for. Now I know, thanks.
Cheers,
Tex
-
1st November 2009, 08:15 PM #13
Great work.
Does not matter what you use, just as long you are happy with the outcome.
-
2nd November 2009, 05:48 AM #14.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Pic 1- A very, very frantic glue-up. Had to work so quick to avoid the dominos binding and making clamping near impossible.
Pic 2- Shows centre panel dry fitted and housings cut for the rails, and the drawer runners mortised. The glue-up sequence was centre divider first, then front two rails 2nd, then drawer runners followed by the back rails.
Pic 3- Shows the completed carcase.
The dimensions of this cabinet are - Back length 2200mm, front length 2000mm, 900mm (h) 500mm (d) and it will have 60mm feet.
-
2nd November 2009, 07:06 AM #15
Another outstanding Domino innovation from Lig.
Similar Threads
-
wine rack
By billc in forum WOODWORK - GENERALReplies: 17Last Post: 14th May 2008, 12:00 PM -
Wine rack
By chris_stam in forum WOODWORK PICSReplies: 1Last Post: 1st June 2007, 03:01 PM -
Wine Rack
By Sculptured Box in forum WOODWORK PICSReplies: 10Last Post: 11th September 2006, 07:19 PM -
wine rack
By timnruth in forum WOODWORK PICSReplies: 15Last Post: 13th June 2006, 12:02 AM -
Another Wine Rack
By Geoff Allen in forum WOODWORK PICSReplies: 3Last Post: 6th December 2003, 11:51 AM