Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Drilling Flat Bottom Holes Query
-
12th February 2015, 01:48 AM #1New Member
- Join Date
- May 2011
- Location
- Mackay, Qld
- Posts
- 4
Drilling Flat Bottom Holes Query
I am looking for a way of drilling flat bottom holes in timber. I am aware of the various types of forstner and saw tooth drill bits but they all seem to have a center spur or pilot which leaves a hole in the middle of the hole. Using a lathe is not viable an neither is a router. Ideally, a forstner or saw tooth bit without the center spike would do the job it it were available. I have thought of grinding off the center spike but this would leave an area in the center without any cutters. Has anyone any suggestions?
-
12th February 2015 01:48 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
12th February 2015, 07:34 AM #2GOLD MEMBER
- Join Date
- Oct 2007
- Location
- vic clayton
- Posts
- 1,042
Depending on the size hole and depth but a router using a spiral bit and hole jig works
Some people are like slinkies - not really good for anything, but they
bring a smile to your face when pushed down the stairs .
-
12th February 2015, 08:20 AM #3Ring Master
- Join Date
- May 2006
- Location
- Lake Macquarie NSW Australia
- Posts
- 402
Buy two spade bits of the size required.
Grind the "spur" and "centre point" off one of the bits.
Using a drill press for safety.
Start the hole with the original spade bit.
Drill down about three quarters of the depth.
Change spade bits and finish off the hole.
This works, this I have done!
Make sure that the second spade bit is in the first hole before switching on the power.
regards,
Ned Black
-
12th February 2015, 08:23 AM #4
Colt MaxiCut Plus forstners are the solution. Rather than a brad point for centering they have a retractable drill bit. You start the hole with the drill bit very short (or a regular forstner) and then take the drill bit out to complete the hole. Rather than leaving a tiny hole at the bottom it is either flat or with a raised nipple (which can be easily removed). I used them to great effect a couple of days ago when I embedded some REMs in my plane till. The magnets had to be within 2mm of the face of the board to have sufficient strength to hold the planes.
-
14th February 2015, 01:24 AM #5New Member
- Join Date
- May 2011
- Location
- Mackay, Qld
- Posts
- 4
Thanks all for your responses.
As I need to drill various sized holes up to a maximum of 54mm, the spade bit would not really be viable.
The "Colt MaxiCut Plus forstners" sound like they may do the job. However, looking at the Carbatec catalog they only list a set containing 15, 20, 25, 30 & 35mm. Also their description and picture do not show a removable center drill so I would need to check this out further.
I found a site which advertises as follows-
"Series 060 Forstner bits are designed for smooth, round or oval boring, cut a perfectly flat bottom hole, and will bore any part of a circle leaving a true polished surface. These bits can be guided in any direction without regard to the grain of the wood or knots. Unlike others, this style Forstner is guided by its circular rim.
Series 060 Forstner bits do not have a center point."
See http://www.jamestowndistributors.com...53&nobot_crawl
This looks to be ideal for what I want to do. However, the supplier is in the US and I can't find an Australian distributor.
-
14th February 2015, 02:20 AM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,793
What's preventing the use of a router - maybe we can find a way around that for you
-
14th February 2015, 06:33 AM #7
-
14th February 2015, 05:47 PM #8
I had a good look at the site you linked to. The bits are in imperial sizes and you are quoting metric for your maximum size. Their 2 1/8" bit is 53.975mm according to my conversion tables, which is a suitable equivalent, but it costs US$128 and is special order at the distributors so probably made to order.
You haven't said how many holes you need to drill in each size, the size of the smallest holes, or the total range of sizes needed. However I suspect that a router with template bushes and a small collection of templates would be cheaper and more efficient way to go for a few parts, or alternatively, look at subbing that part of the job to someone with a CNC router. Either way the only real limitation on a reasonably flat surface is that the router bit has to be smaller or equal diameter than the smallest hole.I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
16th February 2015, 02:50 AM #9New Member
- Join Date
- May 2011
- Location
- Mackay, Qld
- Posts
- 4
Thanks again for all the advice/comments.
The reason I had said that use of a router was not a viable option was because some of the flat bottom holes would be in irregularly shaped wood, e.g. branches etc. However, the majority of the work will be in DAR timber.
So I am thinking I will do what I can with a router and for the others, I will either live with the dimple in the center or perhaps fill it.
Alternatively, for the irregular shapes, I could perhaps saw the timber at the depth of the required holes, drill the holes right through the off cut using a forstner bit and then re-glue the two pieces back together.
Either way I am sure I can come up with an acceptable solution.
-
16th February 2015, 08:45 AM #10Member
- Join Date
- Jun 2012
- Location
- Diamond Creek, Vic
- Posts
- 84
I used to make containers on the lathe for chop stick and incence sticks. The holes were drilled with a forstner bit and were too deep to clean up the dimple with turning tools. I cut appropriately sized disks from matchingn veneer or thin cork and glued them inton the bottom of the holes and hey presto perfectly flat bottomed holes.
-
16th February 2015, 11:36 PM #11
grind the centre pin off a second forstner or spade bit of the correct size and chuck it in a second drill.
Start the hole with a regular forstner bit and drill till you're within 3mm or so of final depth.
swap drills and finish the hole -- the sides of the initial hole will guide second drillregards from Alberta, Canada
ian
Similar Threads
-
A good table saw blade for flat bottom rebates?
By Ausworkshop in forum WOODWORK - GENERALReplies: 6Last Post: 30th March 2013, 03:53 PM -
Best flat bottom cutting saw blade
By Woodtec in forum BOX MAKINGReplies: 6Last Post: 13th February 2009, 08:16 PM