Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 57
-
27th June 2007, 08:08 PM #1Member
- Join Date
- Jun 2007
- Location
- brisvegas
- Posts
- 73
How do i handle rust on my table saw ?
G'day guys. I scored my first saw today (first bit of woodworking machinery to be exact) an ST-12D. I got it for about 1/3 price but it does have some surface rust on the table top. It has not pitted to my eye but its enough to make your finger go a solid rust colour when dragged across it on the table but everything else is fine on the saw.
How do i get it back to a nice polished finish ? I was considering steelwool & a detergent first & then some very fine paper in my little finishing sander. If thats correct then what grade should i sand with or am i on the wrong track here ?
Thanks
-
27th June 2007 08:08 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th June 2007, 08:25 PM #2Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
SilverGlide available from Carpeltec.
Apply it with steel wool if the surface is rusty.
Al
-
27th June 2007, 08:27 PM #3
-
27th June 2007, 08:36 PM #4Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
-
27th June 2007, 09:07 PM #5
Get some abrasive pads, the green "scotch brite" ones or equivilent. Scrub the rust stains off, then hit it silverglide on a lint free cloth, the polish with a clean cloth. After that to help minimise rust returning, I have placed a single sheet over my table. I live within 1 km of the Tasman Sea and have a good clean table.
Pat
Work is a necessary evil to be avoided. Mark Twain
-
27th June 2007, 09:20 PM #6Member
- Join Date
- Jun 2007
- Location
- brisvegas
- Posts
- 73
Thanks guys...i'll give it a try.
-
28th June 2007, 02:29 PM #7Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
I have been using a first treatment of teflon spray then generous amounts of paste wax on cast iron tables.
During the week a couple of drops of condensation from the roof dropped on the jointer top producing some nice orange spots *#!!?Cheers, Ern
-
28th June 2007, 02:49 PM #8
I have a similar problem with my table saw, as I'm still in the process of setting up my workshop and all of my big stuff is still in storage at my brothers place.
Somebody told me to use Camelia Oil which I have purchased from Carba-Tec but haven't got around to doing it yet so I can't tell you yet how it worked.
Cheers
Max
-
28th June 2007, 02:56 PM #9SENIOR MEMBER
- Join Date
- Jun 2004
- Location
- Sydney
- Posts
- 604
I have been using Lanotec for years on all my tools & machines.
Ross
-
28th June 2007, 03:03 PM #10
Up here in the rainforest the only thing that stops my machinery from rusting is engine oil wiped on with a foam pad.
If it goes against the grain, it's being rubbed the wrong way!
-
28th June 2007, 05:20 PM #11Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
-
28th June 2007, 05:55 PM #12Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Al, Teflon spray has got Teflon in it and that can compromise acrylic finishes, which I never use.
You're right to be concerned about silicone which compromises a wider range of finishes apparently.Cheers, Ern
-
28th June 2007, 06:11 PM #13Member
- Join Date
- Jun 2007
- Location
- brisvegas
- Posts
- 73
Thanks everyone. Im starting on it now.
I have no real idea if the saw is a good one (single phase) but its 2001 model & has only been used off & on for pine pallet repair. It seems to run well with plenty of power as ive tried it on some hardwood.
The plastic guard is cracked so i will replace that. Is it a decent saw for $700 ??
-
28th June 2007, 06:12 PM #14
I've used this method a few times with good results to clean the rust off only.
Spray it with WD40 then start sanding with P150 grit. It creates a a rust slurry which you then wipe off with a clean rag. Repeat as necessary. This stops the rust dusting up as you go along. You end up with a nice smooth and clean surface.
I use my old random orbital sander to do this. You'll waste a few discs but its an easy way to do it.
After I've done that, I put on the silverglide.
-
28th June 2007, 06:16 PM #15
Similar Threads
-
Challenge to Create the Ideal Router Table
By rodm in forum ROUTING FORUMReplies: 215Last Post: 26th July 2021, 08:34 PM -
Need advice about GMC router and table.
By strangerep in forum ROUTING FORUMReplies: 36Last Post: 20th April 2007, 09:23 PM -
Triton v Table Saw - A Newbie's Experience
By Manix77 in forum TRITON / GMCReplies: 50Last Post: 18th February 2007, 01:22 AM -
Sliding extension table - out-of-square cuts
By Swagman in forum TRITON / GMCReplies: 3Last Post: 31st July 2005, 08:34 PM -
Sliding table accuracy
By jmaramis in forum TRITON / GMCReplies: 2Last Post: 23rd February 2004, 10:06 AM