Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 29
Thread: How would you make this?
-
2nd January 2012, 04:50 PM #1
How would you make this?
Hi guys
Making a arch way in the garden for SWMBO.
Sizing is it will be made from 90 x 45 treated pine over all hight is 2400 x width 3500. The arch has a diameter of 1340, see attached.
The finished structured will be painted. It will have plants then grown over it.
The question I have is how best to make the arch part and keep the thickness down to 45mm to match the posts?
Hey any other thoughts, please give them.
Thanks
Russellvapourforge.com
-
2nd January 2012 04:50 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd January 2012, 11:05 PM #2
Russell,
how about making the arch by laminating strips of timber around an MDF form?/
You could also laminate from exterior plywood, which i think would be easier.4.5mm should flex around the radius , and 10 lamination's will give you the arch at the correct thickness and will be immensely strong.
Use epoxy glue for your adhesive and step the ends to attach to the posts,
also use epoxy resin to seal the exposed ply edges prior to painting.
jeff
-
3rd January 2012, 09:55 AM #3
That would work admirably.
Cutting kerfs into the 90x45 and filling them with builders bog after bending is another possible alternative to consider.
Cheers
JimBeing happy doesn't mean everything is perfect. It means you've decided to see beyond the imperfections....
-
3rd January 2012, 01:32 PM #4GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Could be done as a segmental arch with pieces cut from 90x90 on bandsaw. Joints either half lap or floating tennon. Glue with epoxy.
-
3rd January 2012, 03:06 PM #5
I was thinking along the same lines of the plywood and the solid wood and just try to think out the easiest one to do but the best structurally over time This depends on me and my quality I guess. Which bring me to what's the best epoxy to use and where do you get it?
Russellvapourforge.com
-
3rd January 2012, 04:23 PM #6GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Boat building epoxy glues would be a good start.
-
3rd January 2012, 05:18 PM #7
I'd go with epoxied laminations for sure. Check out Adhesive Engineering for the most suitable epoxy for your job.
-
3rd January 2012, 09:22 PM #8
Epoxy resins / glue are available from
1, BIAS boating supplies
2, Whitworths ,
3 Bote Cote Australia
4 FGI <
these will be able to supply you with a suitable glue / resin.
Jeff
-
3rd January 2012, 10:24 PM #9
Cutting kerfs into the 90x45 and filling them with builders bog after bending is another possible alternative to consider.
Cheers
Jim
Both these methods would be my choice, both of them being made from the same timber as the rest of the structure and best suited to the proposed project. Both also would I think have a decided cost advantage over epoxy bonded plywood.
JMHO
-
4th January 2012, 05:17 AM #10Senior Member
- Join Date
- Jul 2007
- Location
- Loire , France
- Posts
- 349
If you are building it to last , laminated stuff is allways a risk - I would forget about it , but it's just my opinion .The same goes for kerf bent arches - seasonal changes will make it rot in a single winter . I would definately make a segmented arch , as it's made for front doors (stuff I've done for living for quite some years , BTW) - You make TWO arches , each half of the desired thickness , and then glue &screw them together .The first is made out of 3 pieces , the other of 2 , so the joints dont match.
A church door frame , with the arch made this way fell on the floor by an accident - the door was almost three meters high by two meters wide ( sorry - 9' X 6' 8" - is that so? ) - and heavy beyond belief - much to our surprise , it didn't come apart , not even a slightest crackIt's a slow and painful process...the secret is, dont mind the pain.(Ian Norbury)
________________________
Regards
Ivan Chonov
-
4th January 2012, 11:58 AM #11
Putting in a lot of effort to last just a few years... I would be making the whole thing from steel
....................................................................
-
5th January 2012, 08:38 AM #12GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
-
5th January 2012, 10:28 AM #13
Wow lots of info to get through here, thanks.
Just rang FGI they suggested the R180 epoxy cost about $35 for a 1kg kit (plus $35 to deliver) I have used this epoxy before and found it very good to use.
I like the plywood it is fairly simply to construct just got to be sure that you have no air between the lamination!
Artesano I was thinking also along the same lines of construction. Let me run one idea I had past you all.
CNC out 6 parts from treated pine 30 mm high that make the arch 1/3 of the hight of arch (45mm arch thickness by 30mm high) then put the next layer of 30mm offset by half so that they overlap the lower layer. Then the last layer is a copy of the first giving a total hight of 90mm and a thickness of 45mm.
All epoxy together with some screw to hold it till glue sets.
Seeing that I can cnc the parts out I could lap the joints where the segment meet or even key hole them. Do you think this would help or just be over kill?
Russellvapourforge.com
-
5th January 2012, 04:56 PM #14GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
If you are going to use triple layer you wont need end joints. Only thing is, fresh glued pieces want to slide in all directions even the screws can be a bitch when being driven. Short locating spikes would be better (cut off nails will do.)
-
5th January 2012, 10:58 PM #15GOLD MEMBER
- Join Date
- Aug 2004
- Location
- Perth WA
- Posts
- 2,035
Similar Threads
-
What would you make it from??
By benupton in forum ROUTER JIGSReplies: 4Last Post: 6th April 2010, 10:01 PM -
how to make a sub box???
By Unit_01 in forum HI FI EQUIPMENTReplies: 6Last Post: 14th December 2007, 02:42 PM -
Want to make some furniture in Mordialloc and make some money.
By Lignum in forum ANNOUNCEMENTSReplies: 8Last Post: 23rd April 2007, 12:04 AM -
What do you make of this?
By riri in forum FESTOOL FORUMReplies: 9Last Post: 4th December 2006, 10:35 PM -
Who can make me one of these?
By John G in forum HAND TOOLS - POWEREDReplies: 8Last Post: 7th October 2005, 09:46 PM