Likes: 0
Results 1 to 7 of 7
Thread: joins for a criss-cross shape
-
9th August 2017, 03:02 PM #1New Member
- Join Date
- Aug 2017
- Location
- by the lake
- Posts
- 1
joins for a criss-cross shape
I am making a thread rack for my spools simialar to this one (Cedar House Sews: Threading Up), except with a criss-cross base instead of a square. The vertical part that holds the spools is a piece of rectangular timber 3.5cm 2 x 50cm length which will have drill holes for dowel pieces to hold the spools.
The original plan was to have the base as a criss-cross except I am having trouble figuring out a way to join the criss-cross and place the rectangular rack vertically in the joined base. I don't want to simply nail/screw the pieces together as I want something that does not add extra height. Any ideas? Could I make a rotating base?
Also how do I drill holes on all 4 sides at the given angle (60 degrees) and depth (mid-way) without them intersecting in the middle of the timber. does it matter if they do intersect? (the will be all on the same level). Would too many holes weaken the wood?
-
9th August 2017 03:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th August 2017, 10:50 PM #2
Base - if you are using two pieces, the simplest way to join them is to rebate both pieces 50%. Then you can join using (my preference) screws, nails or staples with or without glue. If your work is to a tight tolerance, you might be able to use glue alone.
Hole drilling - this is probably best achieved by either using a drill press or a jig. For what you are doing it should not matter if the holes join in the middle but if you set a stop on your drill press or bit if using a jig this should not happen. The holes should not weaken the wood to any degree (unless you are supporting an industrial sewing machine on top).
-
10th August 2017, 08:44 AM #3
You could join the base to the upright using pocket holes and 4 pieces of timber to get the cross effect stand. The other alternative would to make the base using 2 pieces of timber and a lap joint, but this would increase the height as the vertical would then sit on top of that.
-
10th August 2017, 04:18 PM #4
I made a much larger version of that to hold my collection of electric chain saws. The post is about 90mm square, and the dowels are 25mm or so, at a shallower angle, holding the handles. I drilled the holes on a drill press with the table tilted, and it doesn't matter if they intersect.
For the base, I used four pieces of wood (~35mm x 90mm vertical) in pinwheel fashion around the post, screwed to the post, and extending about 300mm to some casters to maneuver it about the shop.
A smaller version should work fine for your spool storage.
Cheers,
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
10th August 2017, 06:33 PM #5GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
As woodentree is a new member and might not know woodwork terminology, lap joints, pocket holes, etc, plus may not have access to a drill press.
What state and where is "by the lake"?
For the base I'd screw one end of a piece of 11/2" (40 mm) X 3/4" (19 mm) to the post with a bit of PVA glue, then work your way around till you get the 4 pieces. Once the 4 pieces are attached, screw into the end of the pieces of 11/2" (40 mm) X 3/4" (19 mm), just make sure that they are flat on the bottom, so it won't rock. The 11/2" is the vertical piece, so the 3/4" sits on the table
The pieces will look like a cross with the arms offset.
Pictured below is a lap joint, which will raise the holder by 3/4" (19 mm)
lap joint.jpg
A simple angled drilling jig is pictured below.
angle drill.jpg
Without knowing what tools you have access too, makes it hard to describe what could be an easy fix or a hard way of doing something.
KrynTo grow old is mandatory, growing up is optional.
-
13th August 2017, 11:16 PM #6
Here are a couple pictures requested by Kryn.
Of course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
15th August 2017, 06:42 AM #7
Could something like this work for you?
https://www.youtube.com/watch?v=k4lOeUYoDME
Similar Threads
-
Experimental Instrument Prototype (think wiessenborn cross guqin cross I dunno)
By NebulaGuitars in forum MUSICAL INSTRUMENTSReplies: 9Last Post: 14th April 2010, 10:22 PM -
Joins in decking?
By Tubby2 in forum DECKINGReplies: 8Last Post: 12th November 2007, 06:24 PM -
Handrail Joins
By timbernovice in forum FLOORING, DECKING, STUMPS, etc.Replies: 5Last Post: 13th September 2004, 08:59 PM