Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Joints for 'hall' table project
-
2nd December 2007, 01:12 AM #1
Joints for 'hall' table project
So, the time is fast approaching where work will be forgotten about for a few weeks and spending time in the workshop will be foremost in my mind (and probably with my family but not for the same reasons!).
Recently I was given some old bridge timber measuring about 3m x 330mm x 125mm (I believe its karri) and am thinking that I'd like to build a 'hall' table using three sections. Its not going to be huge (ripping recycled karri would be too costly) but rather I'm going to build it to fill a spot.
The question I have is, would the best joint for fitting the (two) legs to the top be a hidden mortise and tenon?
As mentioned, its going to be a simple rustic table constructed with a top measuring about 2300 x 300 x 100mm and legs of similar dimensions (excepting the length - of course).
Any advice and suggestions would be welcomed.Martin
"Why use new when you can reuse?"
-
2nd December 2007 01:12 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd December 2007, 01:45 AM #2
So....solid ends as legs? like an inverted "U" shape? (from your dimensions)
BillChipslinger
-
2nd December 2007, 01:50 AM #3
Yep - figure they'd be about 150 - 200mm in from either end..... realizing that these won't be the easiest to do, but figuring that they'd be the strongest....
Martin
"Why use new when you can reuse?"
-
2nd December 2007, 07:35 AM #4Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Table
Make sure you don't have any grit and dirt in that timber to ruin your tools.
If you are unsure I'd suggest you get a high pressure water blaster and work it over.
Keep us posted.
-
2nd December 2007, 07:51 AM #5
IMO, yes, a mortise and tenon would be appropriate. It can be hidden, or even a through tenon if you like the look. But, don't make one long tenon, but actually two or three smaller ones. Still strong, but less likely to cause wood movement issues.
If you don't minds the legs slightly proud of the top, you can use a dado. With no aprons for bracing, you want a good, solid join and I assume the table will not be subjected to lateral stress? You might consider a "hidden" brace piece under the top stretching between the legs, or even two of them, but set back so they do not show.Cheers,
Bob
-
2nd December 2007, 09:23 AM #6
I'll be sure to get it as clean as possible - particularly during and after the removal of the old bolts that were used in the original construction of the bridge.
I'll post photos and progress reports as I go...Martin
"Why use new when you can reuse?"
-
2nd December 2007, 09:32 AM #7
Cheers Honorary Bloke - I'll cut a few in some smaller scrap wood to refine my 'skill' in this area. Is the direction of the tenons of relevance (would it be stronger if they're parallel to the direction of the table top or not...)?
Martin
"Why use new when you can reuse?"
-
2nd December 2007, 02:07 PM #8
-
2nd December 2007, 02:55 PM #9
But of course - thanks for the reminder ....
Martin
"Why use new when you can reuse?"
Similar Threads
-
Routing table
By BarryBurgess in forum TRITON / GMCReplies: 4Last Post: 10th January 2006, 06:59 PM -
Bow problem in a conference table
By vern in forum WOODWORK - GENERALReplies: 5Last Post: 17th November 2005, 09:42 PM -
Table Splitting
By treevesd in forum WOODWORK - GENERALReplies: 3Last Post: 19th April 2005, 02:33 PM -
Mick's Router Table
By journeyman Mick in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 11Last Post: 30th March 2005, 06:49 AM -
Miffed over my massage table plans
By bill pentz in forum HAND TOOLS - UNPOWEREDReplies: 42Last Post: 19th August 2004, 10:33 PM