Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Mixing timbers
-
5th January 2015, 02:32 PM #1
Mixing timbers
I have a few pieces work pieces under my belt now, but I have never used different timber in one piece.
I have been given an old 45mm x 3000 mm tassie oak curtain rod. I want to use these as the legs on a chunky stool. I have some 45mm thick pieces of what think might be oregon that Ican glue up to make the board for the seat.
The two timbers will only meet in the holes where the legs are joined to the seat.
Apart from different grain and colour, can anyone see a problem?
Thanks for any tips...
Jorge
-
5th January 2015 02:32 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th January 2015, 07:16 PM #2SENIOR MEMBER
- Join Date
- May 2013
- Location
- Somerset Region, Qld, AU.
- Age
- 66
- Posts
- 602
Jorge,
19th century Chairs traditionally used different timbers for different parts of the chair, especially on Windsor Chairs, so in principal, your idea is probably OK. Not sure about the two species you plan to use. The answer could vary depending on what sort of joinery you plan to use between the legs and the seat. But, if it was me, I'd just go ahead and do it. You'll never know for sure if the idea will work until you give it a try, and it'll be a good learning exercise.
Best of luck with the project.
Regards,
RoyManufacturer of the Finest Quality Off-Cuts.
-
6th January 2015, 01:31 PM #3
I don't se any problems either. Plenty of stuff made with more than one kind of timber and as you say the two only meet at the joints.
Regards
John
-
6th January 2015, 05:12 PM #4
Different timbers may be used for a variety of reasons: for contrast, such as in a table with a light top and dark legs; for structural integrity in Windsor chairs, where one type bends better than another or one is preferred for the carving a seat. Not in the Windsor the timbers may be stained or painted to match one another.
It is important for me that unstained differing timbers compliment one another. To my eye, Tassie oak does not compliment Oregon Pine (the grain is too different and colour is not the same shade). Personally, I would shape the Tassie Oak legs and then stain them dark, and leave the Oregon natural (finish with wax).
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
12th January 2015, 10:58 AM #5
Hi Derek
I agree with you in general. But in this case the different timbers were used because I just wanted to reuse stuff that I havery lying around the shed. The Oregon is highly figured and kind.of pretty, but I did not have enough of it to match the grain during glue up. In fact I only just had enough Oregon for the seat and foot rest.
It's a shed stool that I took on as a quick project for the holidays. I might coat it.in clear PU to make a point of the fact that it's made from recycled materials, or I might paint it... I am rather partial to yellow legs and black top, or vice versa.
Thanks for taking the time to post.
Jorge.
-
18th January 2015, 07:23 PM #6
Three timbers actually
Stool.jpgIMG_8023.jpgIMG_8024.JPGIMG_8025.jpgIMG_8026.JPG
Update: The woodwork is almost done in this project. All that's left is gluing, sanding to high grit value, staining and top-coating with polyurethane. (Gluing is OK, but I hate all the other jobs that are left)
The first picture is the photo on the plans in Australian Woodworking. The other pictures are the result. I had to buy 2m of Tassie Oak rod for the back and center rungs and had a lot left over so I added side rungs. I thinks these add both structural and aesthetic value.
The hand me down curtain rod had a brown finish and a top coat or urethane - It was hard work getting this off by hand so I ended up using a linisher. It turns out that the curtain rod was not Tassie OAK - I am not sure what the timber is - It kind of looks like Tassie OAK but it has a bitter unpleasant smell when cut or sanded... Merbau???
The rungs are Tassie OAK bought new. The seat and foot rest are Oregon, I think. It certainly had a pleasant pine smell when cut or sanded. I had a minimum of Oregon to do the job and as you can see I could not match the grain. This too had been finished with a reddish brown stain, but since this part of the stool is flat, and the wood relatively soft, the job of removing it was much easier. It was only after removing this finish that I discovered that some of this timber was taken from the heart of the tree.
With the round seat, round tenons and the large angled round mortices to take the legs and rungs (all new for me) this was an interesting project. That, and using recycled timber for as much of the job as possible made this an interesting and challenging project. Of which I am kind of proud.
As per Dereks suggestion I will most likely stain the legs and rungs black and leave the seat and footrest clear - or stain with a yellow stain like New Baltic Pine (to yet the yellowed pine look right away, rather than in years).
I hope that you like this as much as I enjoyed making it.
JorgeLast edited by GarciaJ; 18th January 2015 at 07:26 PM. Reason: Grammar, additional notes
-
18th January 2015, 07:48 PM #7
Hi Jorge
That looks fantastic! I'm looking forward to the end result - I could do with one like this in my workshop as well.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
18th January 2015, 08:04 PM #8
-
18th January 2015, 09:40 PM #9
Hi Derek, thank you for the posts. The plans are in Australian Woodsmith #52 page 26. At a pinch I can scan the relevant pages and email you... (better not post them here). There are a few problems with the plans, but it would be pretty hard to work out the angles, etc from scratch.
Jorge
-
1st February 2015, 04:18 PM #10
Finished...
Finished now (well, one more coat of clear PU).
-
3rd February 2015, 10:01 AM #11
Well done.
Similar Threads
-
Mixing It Up
By Nai84 in forum WOODTURNING - PEN TURNINGReplies: 8Last Post: 12th April 2011, 02:11 AM -
Tip for mixing colours
By metester in forum FINISHINGReplies: 2Last Post: 1st July 2010, 05:21 PM -
Mixing Shellacs
By Sebastiaan56 in forum FINISHINGReplies: 3Last Post: 29th January 2008, 08:27 PM -
Mixing woodstains?
By matthewl in forum FINISHINGReplies: 4Last Post: 3rd June 2007, 05:52 PM -
mixing shelac
By Farm boy in forum FINISHINGReplies: 3Last Post: 31st January 2005, 11:49 AM