Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Planing problem
-
30th January 2009, 07:34 AM #1Novice
- Join Date
- Jan 2009
- Location
- London, UK
- Posts
- 15
Planing problem
Got a bit of a problem. Im in the process of making a chair and need to plane the back leg/back rest. I've drawn a simple profile of it below. The problem is I can only plane the inside of it, marked by the red line, only so far before the plane hits the curve. Is there anyway around this without using a sander? I only need to plane a little off to make up for my poor sawing! :s
I was thinking of maybe using a chisel??
-
30th January 2009 07:34 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
30th January 2009, 09:20 AM #2Senior Member
- Join Date
- Jan 2008
- Location
- Vevey, Switzerland
- Posts
- 407
I'd use a spokeshave (but not in this heat )
Cheers, Glen
-
30th January 2009, 09:21 AM #3
How about a rasp, the file, or as mentioned above a spokeshave. They are all good chair making tools
Pat
Work is a necessary evil to be avoided. Mark Twain
-
30th January 2009, 09:47 AM #4Senior Member
- Join Date
- Dec 2008
- Location
- Hunter Valley
- Posts
- 298
Sanding block and increasingly fine papers.
-
30th January 2009, 09:51 AM #5
Best bet is use a rasp, easiest and probably the quickest. But you will have to sand after, just use a sanding block and 80 grit, should clean it up.
Harlan"If you can't kill a zombie with it, it ain't a weapon."
-
30th January 2009, 10:03 AM #6
Jobs like this are usually done by using a router, a straight bit with bearing and a template.
Visit my website at www.myFineWoodWork.com
-
30th January 2009, 10:24 AM #7Novice
- Join Date
- Jan 2009
- Location
- London, UK
- Posts
- 15
-
30th January 2009, 11:28 AM #8
-
30th January 2009, 06:44 PM #9
Try a Hand Scraper
Hi Wood Chip,
If you were looking to take some clean shavings right into the corner you could use a hand scraper. You have total control and could take shavings the width of the leg.
Scott
-
30th January 2009, 08:57 PM #10Novice
- Join Date
- Jan 2009
- Location
- London, UK
- Posts
- 15
-
30th January 2009, 09:10 PM #11China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
As Scott said
-
30th January 2009, 09:26 PM #12
Yes, scraper is the go for in the corner. You can finish up by sanding but a sharp scraper leaves a pretty smooth surface. A router can not leave you with an angled corner but with a rounded corner like the shspe of the bit. Some chisel planes can also get in those kind of places if you have one.
Regards
John
-
30th January 2009, 10:08 PM #13
I too agree with these guys, a cabinet scraper blade. I have recently seen them in Bunnings which was a pleasant surprise, not sure about the quality though but they won't break your budget.
Jim
-
3rd February 2009, 03:13 AM #14Novice
- Join Date
- Jan 2009
- Location
- London, UK
- Posts
- 15
Managed to get hold of a spokeshave. Found it a little tricky to use and I think I screwed up a little but I think I got away with it, just.
Similar Threads
-
Planing Aluminium?
By rhancock in forum METALWORK FORUMReplies: 37Last Post: 11th September 2007, 12:38 AM -
some help with planing and filling
By Shannon in forum WOODWORK - GENERALReplies: 28Last Post: 7th August 2005, 04:48 PM -
Planing thread
By Jack E in forum HAVE YOUR SAYReplies: 2Last Post: 9th June 2004, 10:08 PM -
Planing
By woggit in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 27th December 2003, 08:25 PM -
Planing Timber
By Glen Bridger in forum TIMBERReplies: 3Last Post: 2nd June 2003, 07:42 PM