Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: preserving bark on project
-
10th December 2020, 08:29 AM #1Novice
- Join Date
- Jan 2014
- Location
- sunshine coast qld
- Posts
- 19
preserving bark on project
I have been asked to make a trophy out of a piece of melaleuca timber with the bark still attached. Looking for suggestions how to treat the bark so that the log still looks original.
-
10th December 2020 08:29 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
10th December 2020, 08:55 AM #2GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 1,135
might need a picture of the item?
but other then peeling it off, coating it poly or epoxy and then glueing it back on the bark will eventually flake off.
-
10th December 2020, 09:00 AM #3Novice
- Join Date
- Jan 2014
- Location
- sunshine coast qld
- Posts
- 19
It is typical coastal paperbark type tree. I think it would be nearly impossible to peel off and re-glue. Wondering if a lacquer sprayed on would work.
-
10th December 2020, 09:03 AM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
Bark and wood are different materials so they move and degrade at different rates. I wouldn't risk making a trophy that needs to last for some time with the bark attached.
Someone that uses cactus juice may be able to comment on how successful that might be in stabilising the bark?
-
10th December 2020, 09:56 AM #5Novice
- Join Date
- Jan 2014
- Location
- sunshine coast qld
- Posts
- 19
Thanks for the suggestion .. that was my biggest worry. I am also not sure just how long ago the timber was harvested so my still have too much moisture.
-
10th December 2020, 07:59 PM #6Senior Member
- Join Date
- May 2009
- Location
- NSW
- Posts
- 489
This may seem like a silly idea but many years ago I used to get to watch power poles getting treated with a Creosote based liquid. The poles got loaded into a steel pressure vessel and the vessel was evacuated to draw air and moisture from the wood. The pressure vessel was then filled with the Creosote solution and the vessel then pressurised for a few hours to force the liquid into the timber.
Would a similar system work in this case? Put the timber into a strong container, remove the air and then inject some sort of liquid stabilising agent and then apply air pressure to the chamber to force the liquid into the wood? In theory the liquid should soak into both the bark and the wood as well as filling the gaps where the two meet and glue the whole lot together.
-
11th December 2020, 04:43 PM #7
In Tasmania there is a rather weird tree call Horizontal - Anodopetulum Biglandulosum - which has the rather unique property that it does not (usually) shed its bark.
Horizontal Chair.jpg Horizontal Buttons.jpg
Unfortunately, horizontal is rarely available commercially. Occasionally it is stocked in very small quantities by Island Specialty Timbers, Geeveston, Tasmania.
-
11th December 2020, 07:53 PM #8Senior Member
- Join Date
- May 2018
- Location
- South Australia
- Age
- 54
- Posts
- 272
what you are describing is the normal vacuum pressure process for most treated timber. Whether it would work in this situation I would have no idea. But I doubt joe average could replicate it. You need to create absolute vacuum then fill the cylinder whilst maintaining that vacuum, followed by over 200psi of pressure. Not impossible but very difficult for a once of home based solution.
Cheers Andrew
-
11th December 2020, 08:09 PM #9Senior Member
- Join Date
- May 2009
- Location
- NSW
- Posts
- 489
Well AJ, judging by the treatment plant at Wauchope, now long gone, I would venture to say that almost any decent vacuum pump would do the job. Theirs were rotary vane pumps similar to the machines used on almost every dairy milking bails in the valley and as for air pressure, would it need to be 200PSI to force some liquid into the bark and sap-wood of the timber the OP was talking about? Anyway, it was just a thought.
-
12th December 2020, 06:18 PM #10
Probably not much help, but I seem to remember that about 30 years ago there was a liquid plastic/resin that soaked int soft/rotten timber to stabilise it. Like many other things, I can't remember its name, but you may be able to find something like it by trawling through the interweb.
-
15th December 2020, 10:05 AM #11SENIOR MEMBER
- Join Date
- Apr 2007
- Location
- Sydney
- Posts
- 749
How about making the log trophy, then casting it in a clear resin block? That would preserve everything with no issues of degradation over time.
Similar Threads
-
Preserving some artwork on Plywood
By Optimark in forum FINISHINGReplies: 17Last Post: 19th January 2018, 01:47 PM -
Preserving some history
By ajw in forum BOX MAKINGReplies: 16Last Post: 17th September 2017, 09:51 AM -
Preserving the colour
By Out of Africa in forum TIMBERReplies: 2Last Post: 19th December 2012, 01:29 AM -
Preserving Slabs
By Shane Watson in forum TIMBERReplies: 3Last Post: 21st August 2000, 11:22 PM