Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
17th December 2011, 12:07 PM #1New Member
- Join Date
- Dec 2011
- Location
- Adelaide
- Posts
- 3
My red Gum Slab is curling in on itself - Please help
Hi
I bought a red gum slab four months ago. It was dead wood and had been drying in a garage, properly stacked and aired. I sanded it down and coated it in marine grade polyeurethane. I filled the cracks with red gum dust and wood glue and coated the top five times and the bottom three times. I'm using it as a BBQ preparation slab and i've noticed that it's curling in on itself. It's 2.5m long and both sides are curling in to meet each other. I reckon its curled an inch already, has developed a crack down the middle, or at least widened an underlying existing crack which is letting water drip through.
When I first put the slab on the bbq it was dead flat. Now its heading towards a U shape.
It doesn't have any shade so I don't know if that's affecting it?
Any advice on how I one, fix it and two, stop it from happening again?
I spent ages sanding it, reading forums and making sure I'd got it right but clearly I haven't so any help much appreciated.
Roger
-
17th December 2011 12:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th December 2011, 12:27 PM #2GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,562
Roger,
You didnt say how thick the slab is or how long it had been drying in the garage. Even though the slab was taken from dead timber, you may be surprised how much moisture it could retain. A moisture meter would answer that question. Uneven number of finish coats can sometimes lead to cupping. Backsawn material will also be more prone to cupping. It well may be that you have scored the trifecta and have all three.
What to do now? Check moisture content. Resaw slab along crack and reglue (epoxy.) Check growth rings at end of slab, if backsawn consider turning slab over.
-
17th December 2011, 01:34 PM #3
I would say the fact it is out in all weathers has a lot to do with it. The constant changes in temp and moisture is too much for most bits of timber to cope with. Even if it were seasoned to start with being outside like that has unseasoned it. Under cover it would have a much better chance.
As for fixing what rustynail said sounds about right.
Regards
John
-
17th December 2011, 04:03 PM #4New Member
- Join Date
- Dec 2011
- Location
- Adelaide
- Posts
- 3
Thanks for that. I can move it inside and use it on a bar I was going to build. It is a recoverable situation then ). Would you recommend stripping all the polyeurethane of it, turning it and letting it re-dry?
The slab is 2 1/2 inches think.
I'd imagine the moisture content is now shot as I saw water dripping off the inside where the polyeurethan has cracked cause of the bending.
Any thoughts on the above would be appreciated
-
17th December 2011, 07:43 PM #5GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,562
Roger,
Yes you would need to strip it if it requires further drying. It may not have soaked up too much moisture as it takes a fair bit to get through a lump of hardwood. As the timber was sealed with poly it shouldn't take too long to get back to where it was. For an outdoor application a piece of quarter sawn would be preferable.
-
17th December 2011, 07:54 PM #6
tricky situation. wood keeps you humble as you always need to work with it rather than force it into submission.
strip, re-dry, rip and re-glue are all good options. backsawn is also important to watch out for.
when it's resettled perhaps a design change with some bracing might help keep it stable (allowing for wood expansion metal might be appropriate.) However, 2 1/2" red gum could be quite persistent.My blog: ~ for the love of wood ~ - http://theloveofwood.blogspot.com/
-
18th December 2011, 05:38 PM #7SENIOR MEMBER
- Join Date
- Jan 2004
- Location
- St George area, Sydney
- Age
- 65
- Posts
- 640
Would it need to be dried as if it was newly sawn, i.e 1 year per inch + 1 or is it different when the water is absorbed via the weather as in this case
-
18th December 2011, 06:01 PM #8.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,801
With large pieces of redgum I find you have to place it it situ where it is to be used for 3 - 6 months before you work it into it's final shape. However, taking it out of a dry shed and placing it outside under direct sunlight and rain is just asking for trouble. No (repeat No) clear based finish will enable timber to withstand direct exposure to the Ozzy elements anyway so I would not even bother finishing timber this way unless it was mostly shaded and out of the rain - that's what opaque paint is for.
-
18th December 2011, 10:48 PM #9New Member
- Join Date
- Dec 2011
- Location
- Adelaide
- Posts
- 3
Thanks for that. I've turned it and will start stripping it back over the festive period. I'll clear a space in my garage and it can redry again. Think next time I'll oil it and I'll use it for my bar area. Should be a lovely bar top.
Thanks for all the advice. Really appreciate it.
Similar Threads
-
veneer curling
By TimberNut in forum MARQUETRY and INTARSIAReplies: 14Last Post: 19th September 2020, 08:39 PM -
Red gum slab
By Trent76 in forum WOODWORK - GENERALReplies: 2Last Post: 26th July 2010, 07:12 PM -
see if you can watch this without curling your toes
By mic-d in forum WOODWORK - GENERALReplies: 6Last Post: 23rd April 2009, 11:08 PM