Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
18th June 2017, 02:17 PM #1Member
- Join Date
- Dec 2010
- Location
- Morayfield, Queensland
- Posts
- 51
How do I restore a small patch of fibre floor board
I have a small patch of fibre floor in an caravan about 100mm square that has gone soft due to water damage. It has dried out and I am now left with loose flakes of timber under the vinyl floor covering. It is difficult to get to so replacing the section of floor is not an option. Is there a product I can pump into the area with a large syringe that will soak into the loose timber flakes that will bind them together again and set hard ? It is not an area that is walked so only needs to restore the hard feel of the floor area.
-
18th June 2017 02:17 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
18th June 2017, 04:51 PM #2Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
Some casting resins are quite runny and would probably do what you need.
-
18th June 2017, 07:14 PM #3
That's if the casting resin doesn't run all the way through the flooring.
Also, I think casting resins need a vacuum to prevent the formation of air bubbles.
You could try a runny epoxy. I've been using a fair bit of System Three General Purpose epoxy lately. With the fast hardener the stuff stays "water" runny for around 15 - 30 minutes which should be long enough to inject it into the floor. You would probably only need about 50 ml of the stuff, but I haven't seen it available in quantities smaller than a 1.5 litre pack (1 ltr of Part A, 1/2 ltr of Part B). Most of the epoxies at Bunnings will set too quickly to inject into the floor.regards from Alberta, Canada
ian
-
18th June 2017, 07:21 PM #4
The other stuff to try is super glue -- if you can get a decent enough quantity
like this Low-Viscosity Glue — Hot Stuff - Lee Valley Toolsregards from Alberta, Canada
ian
-
18th June 2017, 07:21 PM #5Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,470
Z-proxy finishing resin is quite runny and stays useable for about 30 minutes. I've used it where I want it to run into crevices, between layers etc. and also over fibreglass cloth. It has excellent adhesive qualities.
-
18th June 2017, 08:32 PM #6Member
- Join Date
- Dec 2010
- Location
- Morayfield, Queensland
- Posts
- 51
Thanks for your replies guys, I was thinking fibreglass resin. I am in Oz so I will give the Z -proxy resin a go which looks similar.
-
19th June 2017, 10:39 AM #7
-
19th June 2017, 11:49 AM #8Member
- Join Date
- Dec 2010
- Location
- Morayfield, Queensland
- Posts
- 51
-
19th June 2017, 02:49 PM #9SENIOR MEMBER
- Join Date
- Dec 2010
- Location
- Melbourne
- Age
- 79
- Posts
- 601
Earl's does go hard ,i have used it on window frames then painted ,so with paint on should be good
Similar Threads
-
Restore back hardwood floor.
By veron in forum RESTORATIONReplies: 2Last Post: 19th September 2009, 09:44 AM -
Worn patch in Floating Floor
By mslaila in forum FINISHINGReplies: 1Last Post: 8th September 2005, 02:18 AM