Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 17
-
15th August 2015, 12:26 PM #1New Member
- Join Date
- Mar 2012
- Location
- melbourne
- Posts
- 6
Sticking wooden quad to powder coated aluminium?
Hi everyone,
We have a large pivoting front door, the surround is all black powder coated aluminium, and the walls are rendered brick. There is a gap of between 3mm to 8mm between the door surround and the rendered wall and I would like to stick a piece of black painted quad there to seal up the gap. I've tried using silicon but that didn't do a very good job at all and pretty much fell off after a couple of days. Does anyone have any suggestions for an adhesive that would bond the quad to the powder coated aluminium?
Thanks!
-
15th August 2015 12:26 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th August 2015, 12:35 PM #2
An 8mm gap is not to big have you considered filling the gap it self
-
15th August 2015, 02:02 PM #3New Member
- Join Date
- Mar 2012
- Location
- melbourne
- Posts
- 6
-
15th August 2015, 02:08 PM #4
Hi,
Liquid nails should take care of that, probably best to glue the quad to the wall rather than the ali frame though.
Regards
Bart
-
15th August 2015, 03:26 PM #5SENIOR MEMBER
- Join Date
- Apr 2012
- Location
- tasmania
- Age
- 58
- Posts
- 116
We normally get some powder coated aluminium angle say 30x10 or whatever size you need and rivet or silicone to door frame.
-
15th August 2015, 03:51 PM #6
You could 'no more gap' the gap. Might need to build it up over a few goes.
Angle as suggested
Quad would work. If you are not worried about it being timber yiu could get some plastic quad. This would be straighter. I would lean towards silicon. Can use masking tape to hold in place till it sets.
A way to get ar I und painti g over silicon is to smear a layer of 'no more gaps' over it or use paintable silicon
Dave TTC
Turning Wood Into Art
-
15th August 2015, 04:28 PM #7New Member
- Join Date
- Mar 2012
- Location
- melbourne
- Posts
- 6
-
15th August 2015, 05:19 PM #8SENIOR MEMBER
- Join Date
- Apr 2012
- Location
- tasmania
- Age
- 58
- Posts
- 116
We get ours from our window supplier in Tas, maybe try one of them, or a sheet metal place could fold one up out of colourbond
-
15th August 2015, 05:23 PM #9
I would be more concerned as why there is that much of a gap and what has caused it. Sort that out first, it seems to be excessive.
The person who never made a mistake never made anything
Cheers
Ray
-
15th August 2015, 05:32 PM #10
Who ever supplied the door should be able to supply the trim
Did they fit it or you
Dave TTC
Turning Wood Into Art
-
15th August 2015, 05:38 PM #11China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
Sikaflex pro
-
16th August 2015, 07:17 AM #12New Member
- Join Date
- Mar 2012
- Location
- melbourne
- Posts
- 6
-
16th August 2015, 07:18 AM #13New Member
- Join Date
- Mar 2012
- Location
- melbourne
- Posts
- 6
-
16th August 2015, 07:20 AM #14New Member
- Join Date
- Mar 2012
- Location
- melbourne
- Posts
- 6
-
16th August 2015, 12:24 PM #15GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 2,947
Sikaflex glue. Tick.
With regards the gap, just get plain aluminium angle, wash with prep wash, sand it down with 600 wet and dry paper to get a keyed surface, wash again with prep wash which will remove any grease, oils from you hands, dust etc. Spray with one of the Colourbond paints which should give you a match for the black door, one spray can will be heaps, you'll have leftovers.
Just a thought.Regards,
Bob
Absence of evidence is not evidence of absence.