Needs Pictures: 0
Results 211 to 225 of 229
-
21st September 2017, 03:09 AM #211
-
21st September 2017 03:09 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
21st September 2017, 05:58 PM #212Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,469
Nows the time to learn how to build sliding doors
-
21st September 2017, 07:36 PM #213
Yes we discussed that.
Haven't gotten around to researching it yet.
is it too late to make them all sliding?
starting to sound really good now.
it would have to be hanging barn door type and not a rolling on the ground type.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
22nd September 2017, 12:53 AM #214
-
22nd September 2017, 06:35 AM #215
-
22nd September 2017, 08:58 AM #216
my thought would be to hang the doors from the ceiling
https://www.bunnings.com.au/diy-advi...-sliding-doorsThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
22nd September 2017, 10:52 AM #217
Three cabinet makers advise to stick to the doors and hinges.
Pretty much all agree its outside the norm.
i.e. retrofittingThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
26th September 2017, 06:10 PM #218
Hands starting to hurt again waiting for doors and hinges to arrive.
Got the top cut back to fit inside.
Then the wiring got a bit complicated.
AirTasker qualified electrician coming tomorrow to sort me out properly.
(Blue to Black, red to brown, green/yellow tracer to green)
IMG_1503.jpg IMG_1514.jpg IMG_1504.jpg IMG_1505.jpg IMG_1506.jpg IMG_1507.jpg IMG_1508.jpg IMG_1509.jpg IMG_1510.jpg IMG_1511.jpg IMG_1512.jpg IMG_1513.jpgThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
28th September 2017, 11:49 AM #219
LED light installed.
Electrician told me had just installed quite a few of these in a factory.
Said the mounting clips were crap and they ended up jelling them to the ceiling instead.
Also mentioned they looked nice and were bright.
IMG_1515.jpgThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
28th September 2017, 11:53 AM #220
OK the extra shelves and doors and hinges have arrived.
The delivery is so much nicer in the early morning instead of in the late afternoon.
Really nice driver as well.
Got to measure, cut and install the edge supports for the shelves.
Then have to research now to mount the doors with system 87 holes
predrilled 87mm from the top and bottom and the other spaced out evenly
with a green cabinet template for the drill holes.
As always Any suggestions greatly appreciated.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
29th September 2017, 02:44 AM #221
TIOmOs HINGE 110° 6075 - Made in Germany
HINGETFULLTL Tiomos 110 Deg Full Overlay Tooless [F01713
https://www.youtube.com/watch?v=lh6PiNUHGyA
Full reveal mounting plate 6035 6220 H2
Tiomos Plate 2mm Adjustable [F058139747]
http://www.grass.at/fileadmin/downlo.../Tiomos_EN.pdfThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
29th September 2017, 03:21 PM #222
Hi Barry
I'm not seeing a drilling dimension of 87 mm.
Apart from the cup holes and securing screws, I'm seeing 32 mm as a standard drill spacing.
Can you point me to the 87 mm dimension?regards from Alberta, Canada
ian
-
29th September 2017, 03:42 PM #223
Hi Ian,
Yes, you are correct. Its just the cup centres.
From the top and from the bottom.
The hinge holes for the plates are 37mm back from the edge.
And 32mm apart.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
29th September 2017, 03:53 PM #224
All the shelves are finished.
IMG_1533.jpg
Got the first door on.
IMG_1547.jpg
IMG_1546.jpg
Finding the centre of the cup - system 87
IMG_1534.jpg
IMG_1535.jpg
I made a test piece before having a go since I couldn't find a step by step procedure.
(Allboard did their best. i.e. not taking any ownership of the actual project. i.e. not being responsible for any misunderstanding nor mistakes etc. Just selling cabinet making products. etc.
But between NOT measuring nor talking about exact measurements and NOT providing any written reference material (just search the internet)
and really trying their best to give unpracticed verbal instructions.
(Then my paranoia, for a slip second, was telling me someone was trying to BS their way thru it.
Then remembering they have alway been super nice and helpful and freaking exact on their cuts.))
I had zero confidence.
These hinges are much better than the ones they sold me 4 weeks ago.
Mounted the first hinge to a door.
Snapped the mounting plate into the hinge.
Then clamped a scrap piece to the plate.
Marked the plate screw holes.
IMG_1536.jpg
Tested the hinge cause I couldn't verify these were full reveal soft close. grrrr
IMG_1537.jpg IMG_1538.jpg IMG_1539.jpg IMG_1540.jpg IMG_1541.jpg IMG_1542.jpg
Removed the scrap piece and made a legend for later referral.
IMG_1545.jpgThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
29th September 2017, 04:17 PM #225
Regretably, again Allboard trying to help as best they could and with what they were allowed to, gave me this to start with.
Frak! I just couldn't work it out before running a test.
IMG_1549.jpgIMG_1548.jpg
Then the numbers started to jell.
32 37 87 (hard to see and upside down)
IMG_1550.jpgThanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
Similar Threads
-
Aussie white woods - suggestions appreciated
By BoomerangInfo in forum TIMBERReplies: 57Last Post: 10th September 2008, 07:54 PM -
Black hearted sassafras and ?? suggestions appreciated
By Brown Dog in forum WOODWORK - GENERALReplies: 15Last Post: 3rd August 2007, 01:48 PM -
Oak CD storage cabinets
By bat in forum WOODWORK PICSReplies: 8Last Post: 1st December 2003, 11:50 AM