Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 44 of 44
-
6th October 2017, 12:26 PM #31Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,470
I deal with Hare and Forbes often. Good service. Many of the thicknessers you are looking at would appear to come out of the same factory or be built to similar specs. The Hare and Forbes one states 1800w but as someone pointed out earlier specs. seem to be, well ??? Of the 4 your’ve mentioned, the Hare and Forbes, IMO, would be the one i’d buy if I was in the same situation. More power, has dust chute, good company to deal with and if you sign up you get a discount on your first purchase.
Noise level is going to be the same no matter which one you buy.
I saved my pennies and bought a 2nd hand Dewalt 735. Even 2nd hand their dear but they are worth the money.
-
6th October 2017 12:26 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
6th October 2017, 01:07 PM #32
As Lappa says, that style are going to be pretty much the same quality and same noise level no matter which brand you buy. Most of the noise comes from the motor as it a spinning at such a high RPM to get the cutter block to spin at 9000RPM.
The only way you will reduce the noise level is to step up to this style but a lot more expensive.
If you are able to do your planning during the day within an enclosed space with windows and doors shut, the noise level outside shouldn't be unbearable for neighbors. Just do half an hour at a time and that will get a lot of timber through and give you a chance to organise what you have completed and get another lot ready.
-
6th October 2017, 07:10 PM #33
-
6th October 2017, 08:00 PM #34
I was only referring to the machine running, not cutting as most of the noise comes from the motor on the portable type. The cutting action would see them both at the same level in regard to noise.
-
6th October 2017, 08:27 PM #35Senior Member
- Join Date
- Apr 2009
- Location
- Wollongong, Australia
- Posts
- 131
Maybe a bit left field.... but if this is a hobby with only occasional projects and time not critical, have you considered going old school and completing project with just hand tools? A lot of these cheap power tools are nothing but frustration and sometimes you might as well just burn the cash instead. Jointing and smoothing a board with hand planes can be an enjoyable and rewarding experience. It is quiet, doesn't fill the air with fine dust, and the tools don't take up any floor space. Decent planes can be easily found second hand, and you could do quite well on a couple of new ones for the money you are considering on the thicknesser. The planes will last forever, those thicknessers won't last long.
-
7th October 2017, 12:14 AM #36Member
- Join Date
- Oct 2017
- Location
- Melbourne
- Age
- 40
- Posts
- 99
Hi Oddy,
I would love to learn to do it but here I need to do it on 100 pieces...it could take me forever...
-
7th October 2017, 08:55 AM #37Senior Member
- Join Date
- Apr 2009
- Location
- Wollongong, Australia
- Posts
- 131
Yeah 100 pieces is a big project - might get a bit old by piece 30 if there is a lot of work to get them flat...
-
10th October 2017, 06:42 PM #38
Hi Jekkil
I have used the Bremen for over a year.
I've found I can take a 3/4 handle bite if I use the middle third of the blade. There is clearance at this place.
Plenty of grunt from 2 blades. Good finish but snipe at both ends, although I can eliminate tail end snipe with upward and forward pressure.
Blades cannot be resharpened and cannot be adjusted and cost between $70 and $90 a set.
I usually thickness about 2mm oversize and bring to size on my Jet sander.
Regards
bandsaw barry.
-
10th October 2017, 08:35 PM #39GOLD MEMBER
- Join Date
- Aug 2016
- Location
- Brisbane
- Age
- 57
- Posts
- 1,315
I also have a big stack of pallets and I'm searching for the right thicknesser at the right price for a hobbyist.
I suspect that the suggestion of using a belt sander comes from a common false assumption. As soon as people hear you are reusing pallets they assume that you are going to make something very rustic or relatively rough and ready.
It doesn't seem to occur to people that you might want to make the most of this wood source. Just because it will be imperfect, I don't see why it can't be properly dressed and flat.
Sent from my SM-G935F using TapatalkMy YouTube channel: https://youtu.be/2_KPRN6I9SE
-
10th October 2017, 10:46 PM #40
I have the old Carbitec version. Had it for years and used it a fair bit. Very noisy and slow. Not chip catcher. Blades are easy to sharpen with a simple jig and sand paper. I wood be using hand plane where possible. It is quiet and no dust. The Melbourne guild of Fine furniture used to rent its large tools for a good price. Look them up and ask current prices.
I am learning, slowley.
-
13th October 2017, 04:35 PM #41Member
- Join Date
- Oct 2017
- Location
- Melbourne
- Age
- 40
- Posts
- 99
Hi guys and sorry for my absence!
I am still deciding what to do as I am know in the process of cleaning my timber.
So I still have some time to decide.
And now here is another question for you.
I was still thinking about the loudness of the thicknesser and I was wondering if it can be compared to a mitre saw.
I have an Ozito Mitre Saw with a 1850 Watt motor and it is quite loud. I definitively can't use it without protections for more than one minute.
Can we say that the thicknesser is equally loud?
-
13th October 2017, 04:37 PM #42Senior Member
- Join Date
- Apr 2009
- Location
- Wollongong, Australia
- Posts
- 131
Much louder probably!
Sent from my iPhone using Tapatalk
-
13th October 2017, 07:32 PM #43
Very much noisier.
-
13th October 2017, 10:35 PM #44
Jekkil, do you have a men's/community shed in your area? If so, they will probably have a floor standing thicknesses you could use for minimal cost. I fear that you will simply end up wasting your money and end up with something unsuitable, or spend way more than you intended after x sets of replacement blades.
If you'll be using pine pallets, a hand plane will actually not be that bad at all. 20 boards a night over a week and you'll be done. (I'm sure one of us who are local to you could give you a crash course in using and sharpening a plane) If on the other hand they're hard wood, you'll spend forever with those bench top players, as you'll more than likely need to resort to many shallow passes per side.
Similar Threads
-
Triton Thicknesser vs Bremen Thicknesser
By Jekkil in forum WOODTURNING - GENERALReplies: 0Last Post: 3rd October 2017, 01:58 PM -
Triton thicknesser
By carworks in forum TRITON / GMCReplies: 8Last Post: 9th July 2014, 11:46 PM -
Triton thicknesser
By Carry Pine in forum TRITON / GMCReplies: 23Last Post: 17th August 2007, 02:25 PM