Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: Waxing in heat
-
27th December 2016, 02:13 PM #1Novice
- Join Date
- Dec 2016
- Location
- Australia
- Age
- 59
- Posts
- 17
Waxing in heat
Hi all, quick qn...
I'm ready to wax a table I've done some pyrography on. I'm using Mastertouch carnauba wax. It's a very hot day (abt 35C in the room where I'll be waxing and where the wax has been stored). Is that ok? When I opened the wax it was soft, with a little pool of melted wax in the centre.
Is it ok to wax in heat? And can I use heat-softened wax?
Thanks
Sent from my iPad using Tapatalk
-
27th December 2016 02:13 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
27th December 2016, 04:05 PM #2
When I have applied carnauba wax to a table top I have found the best way to get an even coverage is to allow the wax to warm up while it is being applied. I usually take an old handkerchief, put a walnut size lump in it and tighten up the ball. The heat of my hand and the friction is enough to get the wax to flow through the cloth and give a good coverage on the wood. I then take to it with a swansdown mop in a power drill to buff it up.
If your wax has melted in the can, and assuming it hasn't obviously separated into something else, I think you might be able to just paint it on. But you would have to go over it with a rag to get an even coverage. Then buff it.Franklin
-
27th December 2016, 04:18 PM #3Novice
- Join Date
- Dec 2016
- Location
- Australia
- Age
- 59
- Posts
- 17
[
If your wax has melted in the can, and assuming it hasn't obviously separated into something else, I think you might be able to just paint it on. But you would have to go over it with a rag to get an even coverage. Then buff it.[/QUOTE]
Thanks v much, fuzzie. Do you usually use one coat, or a couple?
Sent from my iPad using Tapatalk
-
27th December 2016, 05:05 PM #4
I'm not the most experienced user, others might have better opinions, but I did a couple. Not directly one after another, just allowing a couple of days to oxidise/harden up between coats (if that's what happens). It might just be a matter of building up a more even coverage.
Franklin
-
27th December 2016, 05:52 PM #5Novice
- Join Date
- Dec 2016
- Location
- Australia
- Age
- 59
- Posts
- 17
Thanks again, Fuzzie. Will give it a go and see how it looks
Sent from my iPad using Tapatalk
Similar Threads
-
About waxing
By chrisinoz in forum FINISHINGReplies: 7Last Post: 27th December 2016, 04:50 AM -
Waxing a table saw help
By Retiring in forum TABLE SAWS & COMBINATIONSReplies: 10Last Post: 4th February 2016, 09:52 PM -
Waxing Blanks With A Heat Gun
By Paul39 in forum WOODTURNING - GENERALReplies: 7Last Post: 30th August 2014, 01:35 PM -
Waxing over oil
By Dion in forum FINISHINGReplies: 3Last Post: 21st October 2002, 06:44 PM -
Waxing.
By Shane Watson in forum FINISHINGReplies: 0Last Post: 24th June 2001, 12:50 PM