Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Hitchachi drop saw, brake going
-
14th July 2008, 01:38 PM #1
Hitchachi drop saw, brake going
I have a Hitachi 10" drop saw. The blade brake has become very slow to act following power down, and its getting worse.
The saw had had relatively little use, so I'm guessing its dust in the mechanism somewhere. Blowing it out with comp air makes no difference
Before I take it down to clean/investigate, any advice?
I want to be cautious as I love the saw and am the sort of person who generally has bits left over following re-assembly.Bodgy
"Is it not enough simply to be able to appreciate the beauty of the garden without it being necessary to believe that there are faeries at the bottom of it? " Douglas Adams
-
14th July 2008 01:38 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th July 2008, 05:02 PM #2
g'day bodgy, is it the 10fch? I ask because not long after I bought mine the brake started working only intermittently. I took it back to the shop for repair but it seems to have made little difference.
Cheers
Michael
-
14th July 2008, 06:07 PM #3
Yep, with the Laser thingy.
Did the shop say what might be the cause? I'm buggered if I'm taking it anywhere, so if it can't be fixed with a pair of multi grips and a big lump hammer, then I'll put up with it.
Shame cause otherwise its a great saw. 90 degrees = 90 degrees.Bodgy
"Is it not enough simply to be able to appreciate the beauty of the garden without it being necessary to believe that there are faeries at the bottom of it? " Douglas Adams
-
14th July 2008, 06:22 PM #4
Bodgy,
I'm not familiar with the Hitachi saw at all, but a common braking arrangement is to use the on/off switch to short out the motor in the off position. Check that you are fully releasing the switch.
If you feel confident, you could attempt to clean the switch with some form of contact cleaner. (All the usual provisos apply- unplug it first, etc.)
-
14th July 2008, 06:23 PM #5
shop didn't say what the cause was sorry. Like you I couldn't be buggered taking it back another time. I find if you pulse the trigger it will often kick the brake on. Sorry I can't help more.
Cheers
Michael
-
14th July 2008, 06:29 PM #6
Oh, and another point...
If it is the switch, it is worthwhile pointing out that electrical switches are best operated positively/confidently. None of this gently squeeze it, gentle let it off business - sharply on, sharply off is best. Switching slowly promotes arcing and shortens the life of the switch.
-
14th July 2008, 10:20 PM #7
Thanks Chris and Mic, I'll have a go tommorow at the switch. Maybe just another blow job will do it.
Bodgy
"Is it not enough simply to be able to appreciate the beauty of the garden without it being necessary to believe that there are faeries at the bottom of it? " Douglas Adams
-
14th July 2008, 10:40 PM #8
Hi,
I have the Hitachi 12LCH drop saw - same saw just bigger blade & motor. I had the same problem with mine. Just blow out the dust with compressor making sure that the air is dry (no water). Also as Chrisp mentioned open up the switch compartment (Power cord disconnected!), clean any dust which has found its way in, and spray some contact cleaner on the main switch. All is good now. BTW, a new switch would set you back ~$50. You need to clean out the motor housing fairly regularly so that dust doesn't get caught on the carbon brush contacts.
Hope this helps. I agree the saw is very accurate & 200mm crosscut is more than enough when you also have a table saw.
-
16th July 2008, 09:20 AM #9
As advised, I took the switch housing apart and blew it out. I was surprised that it had very little dust in it.
Anyway, I reassembled and the brake now works again.
Obviously a design fault, you'd expect a wood saw to get a bit of dust wouldn't you.
Didn't have any contact cleaner (to be honest I've never heard of it).
Thanks for advice, guysBodgy
"Is it not enough simply to be able to appreciate the beauty of the garden without it being necessary to believe that there are faeries at the bottom of it? " Douglas Adams
Similar Threads
-
Brake press
By gdk3000 in forum METALWORK FORUMReplies: 2Last Post: 1st February 2006, 08:58 AM -
electronic brake on saw.
By joseph84 in forum WOODWORK - GENERALReplies: 5Last Post: 15th July 2005, 01:11 AM