Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: "F" Type Quick Release Clamps
-
13th June 2005, 10:49 AM #1GOLD MEMBER
- Join Date
- Aug 2004
- Location
- Perth WA
- Posts
- 2,035
"F" Type Quick Release Clamps
I have a few of the "F" type Quick Release all metal clamps (non branded Asian crap) that won't hold under pressure. I'm considering notching both edges of the bar with some hacksaw cuts.<?xml:namespace prefix = o ns = "urn:schemas-microsoft-comfficeffice" /><o></o>
<o></o>
Others must have experienced this problem... so I'm wondering what you have done?<o></o>
<o></o>
Thanks.<o></o>
-
13th June 2005 10:49 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
13th June 2005, 11:31 AM #2
Drill a small say 1/8 hole at thread lengths along the bar.
then use nail at back of slide
Regards
Hagrid
-
13th June 2005, 11:31 AM #3
Thats what half of my old clamps have, either hacksaw or old slim taper file to notch the edges(more control), works well enough.
Bruce C.
catchy catchphrase needed here, apply in writing to the above .
-
13th June 2005, 04:13 PM #4
What to do with slipping clamps:
Take a firm grip of the clamp in your dominant hand.
Bring clamp up and over shoulder
Bring arm forward smartly and with maximum force
Release grip on clamp when arm is at or near full extension
Make sure you're facing an area clear of breakables or people
It won't fix the clamp, but it will make you feel a lot better.
Repeated belting with a sledge hammer will also really show it who's boss!
Mick (anger management consultant )"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
13th June 2005, 04:16 PM #5GOLD MEMBER
- Join Date
- Aug 2004
- Location
- Perth WA
- Posts
- 2,035
Originally Posted by journeyman Mick
-
13th June 2005, 04:30 PM #6
Rod,
you can file grooves that will minimise slippage. I'd stay away from the holes and nails, worked with a guy that had really dodgy clamps with this treatment, invariably you're in a rush when clamping up so the end result is nicked and scratched hands from the nails (or worse still, full on punctures :mad: ). One of his clamps ended up being thrown in the drink when it bit the boss.
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
14th June 2005, 12:10 AM #7
There a heaps of "new generation" cheap clamps out there now that work.
Give the dodgy ones the heave.
If they are smalluns the jorgensen coppies from carbatec are about $8 to $12 each & arent bad at all timbecon do simialr ones.
If they are biguns carbatec have some big blue f clamps from time to time that are cheap as chips & seem to work well .
I even got some biguns from super cheap that seem to work ok.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
Similar Threads
-
What is the Ultimate Clamping Kit
By NewLou in forum HAND TOOLS - UNPOWEREDReplies: 21Last Post: 3rd April 2005, 12:22 AM -
Quick action clamps
By Ian007 in forum WOODWORK - GENERALReplies: 10Last Post: 25th June 2004, 09:15 PM -
Hold Down Clamps
By Glen Bridger in forum ROUTING FORUMReplies: 2Last Post: 20th May 2004, 10:01 PM -
Router quick release
By finnster in forum TRITON / GMCReplies: 10Last Post: 31st December 2002, 01:50 PM -
Successful Reto-fit New easy release to old sliding plate
By barrysumpter in forum TRITON / GMCReplies: 0Last Post: 30th January 2001, 08:11 PM