Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 29
-
8th December 2008, 11:04 AM #1.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
First use of BIL mill with 60" bar
I took the 60" bar (purchased from Laurie aka Sawchain) version of the BIL mill out for a run today on the 42" diameter Lemon Scented gum.
The first slabs I cut with the 42" bar and the original short (54") mill rails.
On the third slab using the 42" bar I ran across a problem using the I have not seen before and that is on big logs the bottom part of the mill hits the log preventing milling. Never mind, it just means switching to the 60" bar earlier.
Here is what it looks like on the log rails. Being able to start such a big (33 kgs fully fueled and oiled) mill on the rails makes it a lot easier and safer than starting it off the rails and lifting it up while running
Close up - here you can see the magnetic bar leveling gizmo on the RHS which BTW worked really well - I can now fully recommend this method. I was using regular full comp chain ( I buy rolls of regular full comp chain and file the top plate angle back to 10º over several successive sharpenings) which vibrates the mill a lot more than usual, especially when starting when the bar bounces up-n-down like a yoyo while it established the kerf. I need to switch to Lauries 5 skip chain! Despite the vibration the magnetic bar leveling held on and didn't even look like coming off.
A tank and a half of mix later, slab is cut and here it is idling and cooling off on the log rails.
The 076 didn't seem to have any problem making this cut in this very hard wood. The Aux oiler seems to put out more than enough oil to cover the deficiencies of the 076 oiler. Perhaps not unexpectedly, using such a long chain, chain tension and stretch seems a lot more critical that when using the shorter bar, with the chain coming of the roller nose towards the end of the first cut. No damage to the chain, just a few scratches on the ally nose clamp. In the future I will be stopping a lot more and retensioning the chain during the first use of a new chain.
The vibrations from the comp chain meant I lost a couple of bolts in the sawdust but I now carry lots of spares so it didn't stop me milling. One problem is while the bar started cutting straight, over the length of the slab the bar sag seems to have kicked back in and that the outboard end of the slab was 20% thicker than the start. Apart from wasting wood it's not a problem if the mill is being used to break up a big log bit it is definitely a problem for slabs. Hopefully this will be less of a problem when I file the chain top plates to a full 10º.
42" wide slab.
Close up.
After taking off 5 slabs the loader/forklift was finally able to lift one end of the log up so I could generate a slope.
Mill wouldn't go down by itself - wood too hard and too wide a cut - but effort needed to get mill to bite was minimal.
I have a lot more pics but that's enough for now.
-
8th December 2008 11:04 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th December 2008, 11:58 AM #2
Beautiful looking timber Bob, hopefully you can get it to stabilise so those cracks don't open up anymore. The figure would look fantastic on a long coffee table. How long had the log been sitting?
Cheers,
Mike
-
8th December 2008, 12:29 PM #3SENIOR MEMBER
- Join Date
- Feb 2004
- Location
- kuranda north qld
- Posts
- 717
needs a little fine tuning but good result , and lovely timber . well done ,cheers bob
-
8th December 2008, 02:43 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
Cheers Mike,
Logs have been sitting for just over 5 months so they are definitely not as wet as when they first came in. The consensus is that when the bark turns red and start to fall off this is the best time to mill lemon scented gums. This means they are not too hard but have improved stability because they have been allowed to dry out a bit.
As for a long coffee table, I agree but the slabs as they are would need some thinning. At ~2.5 x 1 x 0.05 m they weight about 125 kg!!!
-
8th December 2008, 02:52 PM #5
-
8th December 2008, 04:29 PM #6Member
- Join Date
- Nov 2003
- Location
- wagga wagga
- Age
- 49
- Posts
- 95
20% thicker at finish try not pushing to hard and also going forward 1 to 1.5 foot then pull back to clear saw dust. This is the method i use when slabbing large slabs with the lucas
-
8th December 2008, 05:03 PM #7.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
Thanks for the feedback but I already sort of clear the saw dust because I normally cut hard wood in a wobble fashion as shown by this picture. I mightn't need to do this if I was using skip chain
This clears a lot of the sawdust out of the cut but I will try this and do this even more - like you say 1.5 ft.
-
8th December 2008, 08:09 PM #8
Beautiful looking timber Bob.
Rather than waiting for the skip chain, why not just cut the teeth off that chain so you have a skip chain? I haven't used my 60" yet, but I bought 2 standard skip chains for it, then ground the teeth off (every second set using the Dremmel) on one to create what I call my super-skip chainNeil____________________________________________Every day presents an opportunity to learn something new
-
8th December 2008, 10:37 PM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
-
9th December 2008, 09:41 PM #10
Beautiful.
Do all LSC Gums look like Blkwood ( inside )?
It's just beautiful Bob. Love it? Do I treasure any LSC Gums that come down here in Vic near me?
TonyDon't pass them by! Be daring and caring!
Dampen their misery....sit with them and talk a little.
Buy them something to eat and a tram fare to a local mission.
I'm so lucky that I've somewhere to live and have family support.
-
9th December 2008, 10:21 PM #11.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
-
10th December 2008, 10:35 AM #12
Always enjoy your slabbing threads BobL, only thing is having to wait while the stuff dries out , but still
-
10th December 2008, 02:10 PM #13
White trunk or red trunk? Bark
I dunno!
The pics you've posted here look as the col of Tas Blkwood. Grain is wider I know.
A little.
Do I need to get my eyes tested?
I don't imagine I'm gonna get that col txtr from a LSGum.
I am familiar with Tas Blkwood.
Just your pics look a little like it. Maybe it's my screen
Can you put up a pic of a strip of bark? From that recent slabbing?
The LSgum I have near me has a white trunk. If I've got my species right.
Anyway. I love what you have produced.
Don't pass them by! Be daring and caring!
Dampen their misery....sit with them and talk a little.
Buy them something to eat and a tram fare to a local mission.
I'm so lucky that I've somewhere to live and have family support.
-
10th December 2008, 09:24 PM #14Ibanez Guest
-
10th December 2008, 09:33 PM #15.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,794
Similar Threads
-
"I see stupid people!" or "spot the blithering idiot"
By journeyman Mick in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 46Last Post: 29th October 2010, 07:29 AM -
Difference "Galvanised" and "Primed" Steel
By Fr_303 in forum METALWORK FORUMReplies: 4Last Post: 22nd January 2008, 05:59 PM -
Comparison Between C.S Mill & Bandsaw Mill
By echnidna in forum SMALL TIMBER MILLINGReplies: 2Last Post: 7th October 2007, 04:26 PM -
Turned "red Ash", and "Hairy Walnut?"
By cedar n silky in forum WOODTURNING - GENERALReplies: 7Last Post: 25th July 2006, 02:01 AM