Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 39 of 39
-
3rd February 2019, 04:58 PM #31GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
[QUOTE=T91;2125230]Just as a matter of interest, I have made up some Gidgee blocks out of a piece we had lying around. Any opinion/info on how Gidgee performs?
As it happens I have some correct dimension Iron Bark in my box of future knife scales and some forest Red Gum, so I will make up half a dozen blocks to test them out. Always good to have spares in the cupboard. I will see if I can locate some Blue Gum in the shed.
Thanks for the explanation[/QUOTE
Would be advisable to run a silica test on Gidgee first.
Forest Red Gum is known as Blue Gum in QLD. Sydney Blue gum doesn't have the same properties.
-
3rd February 2019 04:58 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd February 2019, 05:03 PM #32GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
-
4th February 2019, 01:08 PM #33
Cooktown Ironwood might be worth a try too, it can be burnished to a high gloss using a piece of smooth steel.
Brad.
-
5th February 2019, 07:49 PM #34Senior Member
- Join Date
- Jul 2018
- Location
- Canberra
- Age
- 67
- Posts
- 162
a photo of the HB350A in action with the timber team quarter sawing a London Plane log.
If you look closely, you can see the home made sacrificial wooden dogs holding the log (We have a backer board on the flat face) and wooden guide blocks. Before sawing this log (we were taking off 17mm planks for the box makers) we spent a couple of hours and "leveled" the bed for the work piece to be co-planar within 1mm of the cutting plane of the blade over the entire travel of the track. Possibly a little bit pedantic, but it cant hurt, and we figure it will give us a better chance when we put on a couple of end supports & put a sled on the bed.
As you can see, improving the standard of dust control is still a serious issue
We have discovered that keeping the kerf open with wedges makes things easier, and that lightly pressing on the starter_end of the piece being cut off, at the time we anticipate the cut to finish, allows the board to spring up a tad as separation occurs, which allows it to clear the blade and stay above the log rather than traveling on the blade & hitting the fixed guide blocks
-
12th April 2019, 12:28 AM #35Senior Member
- Join Date
- Jul 2018
- Location
- Canberra
- Age
- 67
- Posts
- 162
IMG_20190411_144445.jpgIMG_20190411_144517.jpgIMG_20190411_144616.jpgIMG_20190411_144626.jpg
Today We added a flip up rear dog to one of the existing rear dogs on the HB350. This makes it possible to roll logs onto the bed with a back stop and secure them to make the face and edge cuts prior to processing the log. Previously we have been making the face and edge cuts with a chainsaw mill outside as the standard dogs wont grip round items much over 150mm diam.
The flip_dog is made from a piece of angle iron mounted to the top of the existing dog, with the flip being flat steel bar bolted to it, with some sharpened threaded rod thru a tapped hole in the end. When not in use it simply folds away behind and below the standard issue dog
Also I re-cut 2 of the Turpentine guide blocks today. They were showing a bit too much wear after about 25 hours of cutting. I have been quite pleased with their performance. I still have not tried out the Grey IronBark guides I made. I'm waiting for the turpentine guides to wear out.
-
16th April 2019, 04:34 PM #36Senior Member
- Join Date
- Jul 2018
- Location
- Canberra
- Age
- 67
- Posts
- 162
New Mk 2 design dogs for the HB350 is pop up type... much better than flip type
and some video of the new dog design in action on some claret ash https://www.facebook.com/actwoodcraf...5136473426476/
-
29th May 2019, 02:04 PM #37Senior Member
- Join Date
- Jul 2018
- Location
- Canberra
- Age
- 67
- Posts
- 162
stretching the limits of the 14 inch horizontal bandsaw at the ACT WoodCraft Guild with a fair sized chunk of English elm culled from the Royal Military College
-
29th July 2019, 06:11 PM #38New Member
- Join Date
- Jul 2019
- Location
- Malaga WA
- Age
- 75
- Posts
- 1
Hi Hilly,
Just seen your post about the Wood-fast HB350 Sawmill / Horizontal Band-saw, which was originally imported by Beyond Tools and the initial models only had a 2HP motor and were basically pro to types only tested at the factory in China. This model has been discontinued and the replaced with 3HP version HB350A please see attached web page for detailed specification http://www.woodfast-group.com/products?cid=482. The Wood-fast group is based out of Brisbane and is the exclusive importer of all Wood-fast machines. Beyond Tools and the exclusive dealer in WA. The HB350A will be demonstrated at the Wood Show this week end (2nd -4th August) at Claremont Show grounds in WA and also at the Melbourne Timber, Tools and Artisan Show 23-25th August at Melbourne Show Grounds. I am the business manager at Beyond Tools and would be happy to provide any information that any member requires. Good Luck, Francis
-
30th July 2019, 07:55 PM #39Senior Member
- Join Date
- Jul 2008
- Location
- geelong
- Posts
- 359
some many years ago bought a 20" 3HP bandsaw with the primary purpose of resawing -had close to a 12" cut needs work on the top guide at the moment -but has done some impressive things -bit dangerous -malee root slices in particular. Have heard of small wheel band resaws -presume that the blades are a particular hardness as small wheels flex the blade much more. Once delt with a -say 8" wheel metal cutting bandsaw that could cut 6" height -had blades made for wood for it-frequent breakage. My current -no breakage however the odd nail etc. and the issue with the guide is the rear (back of blade) guide seized and the blade ate through the bearing - can and have got new bearing. still needs a sleave to cover the width. About 1/2" or so. bearing itself is only 4mm or thereabouts
Similar Threads
-
Resaw jig required for bandsaw
By Dengue in forum BANDSAWSReplies: 7Last Post: 1st March 2013, 04:42 PM -
Anyone own a Makita resaw bandsaw
By INVENTOR in forum BANDSAWSReplies: 19Last Post: 5th January 2013, 08:19 PM -
What is the best resaw Bandsaw
By woodturner777 in forum BANDSAWSReplies: 10Last Post: 22nd August 2012, 02:05 AM -
Resaw Bandsaw
By woodturner777 in forum MUSICAL INSTRUMENTSReplies: 0Last Post: 12th August 2012, 10:00 PM -
Bandsaw Resaw sled
By Peter36 in forum TIMBERReplies: 5Last Post: 28th December 2005, 07:45 PM