Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
19th July 2018, 06:40 PM #1GOLD MEMBER
- Join Date
- Aug 2016
- Location
- Brisbane
- Age
- 57
- Posts
- 1,315
What width to rough saw small logs?
I have a stack of small logs that another forum member kindly donated a year ago.
There is Red Ceder, a little messmate and some hoop pine.
I am going to rough saw it on a 14" bandsaw. (Will see about the messmate).
Unfortunately I didn't get around to painting the ends and so they have dried and some have checked/cracked. But once I finish some other things, I want to get this stack of logs into some rough sawn timber planks for future use.
I am not sure what I am going to use each piece for. Probably small items like lamps, boxes, whatever I think of etc. Possibly some small table legs. So I don't know what dressed thickness I should be aiming for.
Should I aim for around 25mm or around 18mm dressed thickness?
If I decide to aim for 18mm thickness dressed, then is 25mm rough sawn appropriate?
If I aim for about 25mm dressed, then is 32mm rough sawn appropriate?
Should I just take each log and divide it by any number that gives me something approx 30mm thick, rough sawn?
Remember I am a beginner so I wont get as much yield as some of you experienced guys.
-
19th July 2018 06:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
20th July 2018, 12:26 AM #2GOLD MEMBER
- Join Date
- Apr 2015
- Location
- Warragul Vic
- Posts
- 1,093
Assume these are small diam logs of 5-8" diam (to 200 mm) and fairly straight? Cutting these on a bandsaw takes some skill and experience cutting rounds so be careful to avoid blade catching and rolling the log.
I reckon you should first saw them in half lengthwise, dock them to remove worst splits and coat the ends eg with cheap acrylic paint (eg undercoat) to seal and let these 1/2 logs dry for a couple of years (in a cool dry place) and then do some resawing into boards or squares etc for the small items you suggest. This will give you time to think and plan what you wish to make after they have finished drying, shrinking, warping and recovery can be more predictable.
Just my suggestion which you can take or leave
-
20th July 2018, 11:18 PM #3GOLD MEMBER
- Join Date
- Aug 2016
- Location
- Brisbane
- Age
- 57
- Posts
- 1,315
Thanks. They each have some sort of flat face so I hope it shouldn't be too risky to resaw them.
Sent from my SM-G935F using TapatalkMy YouTube channel: https://youtu.be/2_KPRN6I9SE
-
20th July 2018, 11:23 PM #4GOLD MEMBER
- Join Date
- Aug 2016
- Location
- Brisbane
- Age
- 57
- Posts
- 1,315
I'll test them again in a few weeks but I think they are dry already. At least dry by humid QLD standards.
Sent from my SM-G935F using TapatalkMy YouTube channel: https://youtu.be/2_KPRN6I9SE
-
21st July 2018, 12:23 AM #5SENIOR MEMBER
- Join Date
- Dec 2011
- Location
- SC, USA
- Posts
- 612
My #1 rule of resawing is "Don't be greedy".
Unfortunately - bandsaws are wood wrecking demons. The "quality" of the resaw cut depends heavily on the setup, the blade, and your skill.
Now cross this with green wood - which will cup, twist, and go lumpy during drying.
Remember it's much easier to take more wood off at the planer than it is to put it back on.... And since this is timber - the "wood" is free.... You will "Loose" a lot more on the back end if they don't clean up till they get to 15 or 16mm...
I would start at least 6mm oversize on the first log. Maybe even 8mm to ensure you have enough thickness left
Don't be greedy...
-
21st July 2018, 12:05 PM #6New Member
- Join Date
- Mar 2014
- Location
- Canada
- Posts
- 1
Hi from Canada. I have done what you are proposing. I have cut 6 foot (1.8m)by 10 inch (250mm)diameter elm logs with a sled apparatus that l constructed. In my experience the saw band will drift. I tried to cut 2 inch (50mm) thick pieces and due to blade drift and warpage during drying l lost a larger percent of wood than necessary. If l were to do it again l would cut no thicker than 1 1/4 inch (32mm)and laminate to make thicker material. It will dry quicker as well and warp less if you weight it down and stack it well to allow air circulation after cutting. Good luck.
-
21st July 2018, 09:33 PM #7GOLD MEMBER
- Join Date
- Aug 2016
- Location
- Brisbane
- Age
- 57
- Posts
- 1,315
These photos show the stack of logs with their faces and cracks. Perhaps that might help you give me advise.
Sent from my SM-G935F using TapatalkMy YouTube channel: https://youtu.be/2_KPRN6I9SE
Similar Threads
-
Diablo 184mm & 254mm 40t body width & riving knife width for table saw?
By Matt NQ in forum WOODWORK - GENERALReplies: 22Last Post: 16th April 2018, 03:13 PM -
Questions for small logs
By typicalabc in forum SMALL TIMBER MILLINGReplies: 5Last Post: 29th June 2017, 11:33 AM -
In praise of small logs
By THE BARON in forum SMALL TIMBER MILLINGReplies: 19Last Post: 23rd June 2016, 12:52 PM -
How to rip cut a pallet plank with small width
By quochuy in forum WOODWORK - GENERALReplies: 13Last Post: 20th March 2015, 06:40 AM -
Milling Some Small Logs at DJ's Timber
By Groggy in forum SMALL TIMBER MILLINGReplies: 4Last Post: 2nd June 2008, 11:24 AM