Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: Router for starting out
-
21st December 2014, 01:44 PM #1New Member
- Join Date
- May 2013
- Location
- Perth
- Posts
- 9
Router for starting out
Hi all,
I'm an amateur weekend woodworker and I'm at the point where I've been given the all clear from the commander in chief to purchase a router. I'm seeking some input on a router purchase. I'm looking at the 1010W JOF001, the 1400W MOF001 and the 2400W TRA001 and using justtools as a price indicator ($249, $329, $349) and I'm generally quite value-conscious.
I typically work on plywood, pine, MDF, but recently have used some meranti (I believe) from some old architraves/skirtings. And I'm not sure if I will go for more than filleting, chamfering and simple plunge cutting with a straight bit at a depth/radius of up to 8mm.
Would the 1010W suffice, or should I bite the bullet and go for the extra features in the 2400W? Safety-wise, as I am new to routing, would it be safer to start off with a lower power for less kickback when I do something stupid?
Finally, as I read about routers, I've seen stationary (for mounting on tables) and plunge routers, but when I walk through the shops here, they all seem to be plunge routers that can be mounted in tables. Is this correct?
Thanks!
-
21st December 2014 01:44 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
21st December 2014, 06:30 PM #2
I have both the JOF and the TRA in my router collection (7! ), the TRA is used in the table only and the JOF for handheld. If I absolutely had to come down to only 1 () it would be the big TRA over every other router I have.
For handheld work any big router is a little awkward to use but the extra mass is useful as it takes a lot to move it off the path you've chosen. The soft start works well and really limits the kickback on starting.
Where this machine (and all other big 1\2" beasties) really shines though is mounted in a table. I pretty much always use a router in a table if at all possible. My very first "table" consisted of screwing a small sheet offcutof 1\4" ply onto the baseplate of a DeWalt 625 and clamping the whole lot in a Black & Decker Workmate. The fence was a batten clamped to the ply. Very simple but effective.
-
21st December 2014, 06:55 PM #3
I started with a very powerful Makita 3612 which my wife surprised me with at Christmas many years ago before I was much into woodwork. I have since gone down in sizes on two more routers, being the smaller Triton and a Ryobi laminate trimmer. All are excellent routers and all get regular work,in my home hobbyist workshop, albeit these days, the Makita permanently lives in a home made router table. I use the small model Triton as my plunge router.
The Makita is a beast of a machine but it has proven to be a very versatile machine over the years. Its only disadvantage has been that it was manufactured before the availability of a soft start machine but you learn to live with that, after a while, by not switching it on too close to the work piece. The laminate trimmer is not far behind in terms of its utility because it is so easy to put a small round edge on a work piece with a light little one hand router.
Sooooo - my recommendation would be to get the biggest plunge router, preferably with a soft start, that you can as a starting point and then a little while down the track, get a laminate trimmer. Don't be misguided by the term, "laminate trimmer"; they are a proper router, but without the plunging facility and they only take 1/4" shank router bits. They are however, soooooooo handy and augment, well, the bigger muscle router that you will use for big roundovers, raised panel profiles, deep grooves, pattern routing into very thick stock, etc.
When you do have a muscle router as your first, you will be surprised at how often you will use it.
The incremental cost of the laminate trimmer will be easier to sell to SWMBO after you have the first big one than the other way around, of course.
-
28th December 2014, 07:25 PM #4
I own all three of the routers you mention and have used Triton routers for many years. I have reviewed all three and this page features the smallest, with links in the first paragraph to the other two models. I hope you might find it useful. I believe the the MOF001 might suit your needs best at the moment, as you can readily use it freehand or in a table.
As you're new to routers, then this page may assist. Any further/supplementary questions, let me know.
Ray
Similar Threads
-
Starting Up
By Robert Bivens in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 6Last Post: 7th December 2012, 01:17 AM -
Starting up again
By dopeydriver in forum Michael Storer Wooden Boat PlansReplies: 8Last Post: 3rd August 2010, 03:44 PM -
Hello - Just starting out
By ch00k in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 6Last Post: 5th May 2010, 09:07 PM -
just starting!!
By 5.8L95f150 in forum WOODWORK - GENERALReplies: 12Last Post: 20th January 2006, 07:04 PM -
Starting out on the router
By morwong in forum ROUTING FORUMReplies: 6Last Post: 3rd April 2005, 10:15 AM