Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 22 of 22
Thread: Gent's saw
-
2nd August 2016, 12:01 AM #16
Thanks Paul. I wonder what is meant by 'varnished edge'?
Innovations are those useful things that, by dint of chance, manage to survive the stupidity and destructive tendencies inherent in human nature.
-
2nd August 2016 12:01 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd August 2016, 12:32 AM #17
Rob
I think "varnished" edge is the same as "polished" edge, which is the terminology used by Simonds. It refers to the curved part of the handle that is gripped by the hand. It shows up as a slightly different colour, although this could be due to it being effectively end grain and does seem to be smoother. What I don't know is how they achieved that. I might have to do some research on the process.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
2nd August 2016, 12:35 AM #18GOLD MEMBER
- Join Date
- Mar 2010
- Location
- US
- Posts
- 3,127
If you separate it from the saw, and give it a full carpenter saw cheek, you can come up with a pretty good profile. Spear and jackson had some profiles that had a pretty thin top line (though the notch cut was much steeper).
That'd be my lloyd's money guess, that it was cut from a carpenter's saw pattern, but it would be difficult to prove, for sure.
-
3rd August 2016, 04:00 PM #19
I chanced on this saw on Ebay while looking for something completely different: Peugeot Freres:
Peugeot Freres 9ppi. 11 inches.jpg
Slightly reminiscent of the Buck saw. This example was 9ppi
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
4th August 2016, 09:33 AM #20
Jim Bode has one listed too.
jim bode saw 080316.JPG
Rare! 8 inch 11 point Crosscut DISSTON/JACKSON NO. 00 Hand Saw circa 1887-1940Innovations are those useful things that, by dint of chance, manage to survive the stupidity and destructive tendencies inherent in human nature.
-
5th August 2016, 12:52 PM #21
Got it. Blade at the toothline is 0.042" and it's 0.038" 1 cm up from the toothline and 0.028" at about 1 cm in from the back. At the very edge it measures 0.025". These measurements taken a near the etch. The width of the set teeth under the handle, where there is the least wear evident, is 0.059".
Innovations are those useful things that, by dint of chance, manage to survive the stupidity and destructive tendencies inherent in human nature.
-
5th August 2016, 02:48 PM #22
This is the similar saw I inherited from my father:
Father's saw.jpgFathers saw.jpg
12" long, 8ppi, compression style rivets and to my mind of sentimental value only particularly as it has a slightly wavy blade. Actually the best aspect of this saw is the handle. It appears totally undamaged!
I did a quick scrub on the face side but was unable to determine any sort of etch. I think something was there once upon a time.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
Similar Threads
-
Gent's JR
By Dalboy in forum WOODTURNING - PEN TURNINGReplies: 0Last Post: 30th March 2015, 03:44 AM -
First JR Gent
By toddbron in forum WOODTURNING - PEN TURNINGReplies: 2Last Post: 11th June 2012, 08:52 PM -
Jr Gent
By Pariss in forum WOODTURNING - PEN TURNINGReplies: 6Last Post: 26th November 2011, 01:04 PM -
23-09-11 Jr. Gent
By timboclark in forum WOODTURNING - PEN TURNINGReplies: 4Last Post: 24th September 2011, 10:29 AM -
12-8-11 JR. Gent
By timboclark in forum WOODTURNING - PEN TURNINGReplies: 6Last Post: 3rd September 2011, 11:19 AM