Results 1 to 15 of 789
-
23rd October 2012, 08:51 PM #1
Plane Blades and Chisels ( A progress report )
Hi All,
Things are getting back to normal ( at last ) and grinding is progressing nicely. Helmut is coming up in a few weeks to help with packing and postage.
Here are a couple of short video's
Setting up..
Setup for Grinding Plane Blades - YouTube
Grinding the bevel..
Grinding the bevel - YouTube
Josh is spending time working steadily through the finishing stages of the plane blades...
A thread in the Metal work section describes how the 25 degree mag transfer block was made. https://www.woodworkforums.com/f65/ma...-block-160111/
Thanks to everyone for being so patient.. it's a marathon.. and it's not finished yet..
Regards
Ray
-
23rd October 2012 08:51 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
23rd October 2012, 09:11 PM #2
RayG - Thank you for the update, I will send out a PM to everyone asap to direct them to this thread. - Helmut
-
23rd October 2012, 09:28 PM #3
Plane Blades and Chisels ( A progress report )
Looking impressive, good to see. Thanks for the vids and the update.
An afterthought. When was the video taken, how recent is it?
Ray153
Sent from my iPad using Tapatalk HD
-
31st October 2012, 07:23 PM #4
Hi All,
Just continuing on from the previous post,
As the blades come off the surface grinder, there is the familiar wire edge, and we are taking that off with a few swipes on a Shapton 5000.
I'd expect that some might want to go further with polishing and flattening the back, but as supplied it will pop hairs off your arm.
The blade edges are then dipped in a Hot Melt Strippable Protective Coating
If nothing goes wrong, all the plane blades will be finished this week. ( no promises..)
Regards
Ray
PS..An afterthought. When was the video taken, how recent is it?
Sorry Ray, I missed that question, video was taken the same day as it was posted.
-
31st October 2012, 11:08 PM #5
Ray
It's looking good. Nice work with the magblock and thanks for the update.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
1st November 2012, 11:48 AM #6
To Ray , Helmut and Josh
Marathon is right. There sure is a lot for you to do. Will that shiny mirror like finish that we saw on the plane blades be on the firmer chisels too? Boy the small set of chisels you are doing for me will certainly be beautiful heirloom to be handed down to who ever is around when I am gone.
Thanks you all so very much for the care and attention you are displaying with this huge group order.
Now I just can't wait for them to arrive. I need now to gather some really good timber to make the handles.
All the best to you fellas and thanks againJust do it!
Kind regards Rod
-
2nd November 2012, 05:00 PM #7
SENIOR MEMBER
- Join Date
- Oct 2012
- Location
- Australia
- Posts
- 765
Some extra love
Hi all,
(Josh here; thought i should finally join the forum so that I can post some updates of the group order without having to bother RayG about them)
Well the plane blades are almost finished only a dozen or so to go!
The only remaining blades are the ones that require that extra special bit of attention to put right.
Attached bellow are two typical examples.First one is a 6mm x 200mm x 50mm Blade that had a 0.13mm twist.
Second one is a 6mm x 200mm x 50mm Blade that had a 0.11mm Bow.
It is very time consuming (all day to just finish of 6 blades) but it is worth it to have flat backs.
PS.chambezio,We will do our best and if nothing else they will as flat as possible on the chisel backs to make that initial honing as painless as it is possible to be with cryogenic M2.
PPS. I just put one of the ground blades (the "skin" needs to be removed as the there is a layer of different steel after heat treatment) on the hardness tester and it pulled a just a little more than our 64.8HRC Wilson's Standard Calibration disk. so I would say that the blade is 65±0.5HRC which would explain why my shaptons are only just adequate for the job of sharpening the grinding burr off the bevel.
-
2nd November 2012, 07:39 PM #8Bushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
2nd November 2012, 08:23 PM #9
Welcome Josh.
Brobdingnagian post shows a level of care that we have never gotten from any of the commercial mobs. As I have said before Brobdingnagian and RayG are going way beyond the call of duty, for the love of perfection in their work. While delays have been frustrating the end product will exceed all your expectations and will be superior to anything done in the past.
-
2nd November 2012, 09:05 PM #10
Senior Member
- Join Date
- May 2008
- Location
- Vermont, VIC
- Posts
- 238
-
3rd November 2012, 12:42 PM #11
Brobdingnagian
... hmmm ... I thought you'd be taller...
-
3rd November 2012, 10:58 PM #12
SENIOR MEMBER
- Join Date
- Oct 2012
- Location
- Australia
- Posts
- 765
So did I.... :S
-
6th November 2012, 04:29 PM #13
SENIOR MEMBER
- Join Date
- Oct 2012
- Location
- Australia
- Posts
- 765
Plane Blades are almost done.
NOTICE:The people that have ordered plane blades should send an updated/current delivery address to Thumbsucker/RayG/Brobdingnagian via PM or email.
NOTICE:The people that have ordered skew blades will not have a bevel ground unless you can tell me which way you would like it ground. (a picture would be best to avoid confusion)
-
6th November 2012, 08:50 PM #14
Ahhh, now I see what has happened to my riving knife, its been cut up into little pieces, hardened and sent all round Australia...lol
Nice work Guys, seriously, you have been busy I know, Holidays are not far away, could be time for a visit down your way !
Melbourne Matty,
Ducking for cover......
-
6th November 2012, 09:42 PM #15
SENIOR MEMBER
- Join Date
- Oct 2012
- Location
- Australia
- Posts
- 765
Your rivin' knife is sitting here somewhere nicely ground and oiled just exactly where is another question :S, I think we got a little caught out by the Austrian adventure. Shall we post it off for you or should we wait for your company?
Your always welcome by the way.
Similar Threads
-
progress report
By texx in forum WOODTURNING - PEN TURNINGReplies: 10Last Post: 16th June 2009, 09:18 AM -
Starting up - progress report
By BoomerangInfo in forum WOODTURNING - PEN TURNINGReplies: 14Last Post: 21st September 2008, 05:25 PM -
jig for honing chisels and plane blades
By Farm boy in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 16Last Post: 12th February 2006, 08:46 AM -
Luthiery Workshop - progress report
By kiwigeo in forum WOODWORK - GENERALReplies: 7Last Post: 10th October 2005, 08:26 PM -
KS-12K progress report.
By BobR in forum HAND TOOLS - POWEREDReplies: 23Last Post: 25th November 2004, 03:22 PM