Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
-
10th November 2018, 05:28 PM #1New Member
- Join Date
- Nov 2018
- Location
- Mandurah western Australia
- Age
- 73
- Posts
- 3
Suitable wood for hand carving small figures
Hi everyone. Very new to both this forum and hand carving. Just purchased a small carving blade (two cherries) but am having trouble carving into a piece of pine purchased from local hardware store. It doesn’t seem to slice through the wood like the YouTube videos I have watched. Question is are there any woods available in Western Australia that are similar to the Basswood used in the videos? If not can I order some from the east?
-
10th November 2018 05:28 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
10th November 2018, 10:12 PM #2
I think the sharpness of the chisel could be the problem . Sharp chisels don't have problems with most woods but specially Pines . Pine can be soft enough to not leave crisp fine edges maybe . Is it as sharp as it should be ? And do you know how sharp that is ? The standard for carving chisels is VERY sharp .
Rob
-
11th November 2018, 09:08 AM #3
Hi Derwick, welcome to the Forum. You would have been better off posting this query in the "Timber" section - more likely to be spotted by a local who could guide you on what's available in your area.
I'm with Auscab in that the major contributor your problem is quite likely the edge on your chisel. If you are using straight out of the box without honing or stropping, it is probably far from sharp enough.
It can depend on which pine you are trying to carve, too. Over your way, I assume you will be using P. radiata, which can be anything from soft & crumbly to tough as old boots with marked earlywood/latewood variation which makes carving detail exceedingly difficult even for an experienced carver. Hoop pine would be a better choice if you can get it, being a far more homogenous wood. There are several excellent carving woods over this side, but they are not likely to be easily obtainable in W.A. Maybe a local will chime in & help out....
Cheers,IW
-
11th November 2018, 01:29 PM #4New Member
- Join Date
- Nov 2018
- Location
- Mandurah western Australia
- Age
- 73
- Posts
- 3
Thank you for the response. The chipping knife I purchased was new and I did strop it before use. The edge angle looks about 30degrees. I would be interested if there are any ‘Whittlers’ in WA that could give advice on available timer suitable for carving. Also what type of equipment they use. Thank you for the forum.
-
11th November 2018, 09:53 PM #5
WA Carvers Guild are in Wandi every monday morning. WA Carvers Guild Wandi
Similar Threads
-
Hand Carving
By MalleeAnt in forum WOODWORK - GENERALReplies: 1Last Post: 18th July 2017, 09:49 PM -
Producing wooden Handles suitable for small cabinets
By Template Tom in forum ROUTING FORUMReplies: 0Last Post: 4th April 2017, 04:24 PM -
Small wood turning lathe for pens - Wanted - second hand or new
By gillscott in forum GENERAL & SMALL MACHINERYReplies: 2Last Post: 15th January 2016, 04:21 PM -
Suitable woods for carving eating/cooking spoons
By Heavansabove in forum WOODCARVING AND SCULPTUREReplies: 5Last Post: 7th June 2013, 04:08 PM -
Suitable Aussie timbers for Chip Carving
By Sebastiaan56 in forum WOODCARVING AND SCULPTUREReplies: 13Last Post: 6th August 2009, 10:00 AM