Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Unknown holes
-
31st May 2016, 11:18 PM #1Senior Member
- Join Date
- Nov 2012
- Location
- Mid North Coast NSW
- Posts
- 106
Unknown holes
Another garage sale tool I'm gonna clean up and use.
It's a Silex No.78.
P1030342.JPG
so... What's with the 2 holes ?
P1030345.JPG
-
31st May 2016 11:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
1st June 2016, 09:37 AM #2
No idea! they aren't on the one I inherited from the old pot. Apart from the fact they don't feel all that friendly in the hand (no wood anywhere!), and that cheap-looking locking key, they are a very useable & practical bevel. The blade locking mechanism works extremely well.
Cheers,IW
-
1st June 2016, 02:45 PM #3Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
The holes may indicate that silex bevel was used to mark out repeated cuts to traditional roofing members.
Stewie;
-
1st June 2016, 06:19 PM #4Novice
- Join Date
- Jan 2016
- Location
- Central West NSW
- Posts
- 17
-
1st June 2016, 09:48 PM #5
Are they threaded?
TTLearning to make big bits of wood smaller......
-
2nd June 2016, 02:13 AM #6
-
2nd June 2016, 10:33 AM #7
Yes, those two ideas may offer a clue, particularly if you measure the distance between the hole centres and the diameter of the holes. For example, if they are 90-91mm apart (internal to internal edge of hole) then it would possibly suggest that it was repetitively used to sit over a 90mm wide piece of timber.
If they are threaded then my estimate would be that a couple of pins were screwed into place to sit either side of (say) a roofing member as Stewie suggests, for repetitive use.
If not threaded then they may have just received pins from a jig of some sort in a workshop situation.
-
2nd June 2016, 05:29 PM #8GOLD MEMBER
- Join Date
- Jun 2003
- Location
- Sunbury, Vic
- Age
- 84
- Posts
- 2,722
There are no holes in the Silex #78 which I inherited from my Father-in-law so it is obviously peculiar to yours and the suggestions made by others are possible.
Tom
"It's good enough" is low aim
-
4th June 2016, 01:30 AM #9GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
I would say that the holes if threaded, were used to screw a plate on, so that angles could be marked on something that had a large radius.
KrynTo grow old is mandatory, growing up is optional.
-
4th June 2016, 01:13 PM #10
I wondered that, but you can see that there is extensive wear over the area between the two holes, so if something like a plate was screwed to to it there area should be a clear patch where is once was.
Of course the gauge could have had several different lives, so the holes could be totally unrelated to the wear.
TTLearning to make big bits of wood smaller......
-
4th June 2016, 03:52 PM #11Senior Member
- Join Date
- Nov 2012
- Location
- Mid North Coast NSW
- Posts
- 106
Sorry I didn't get back earlier.
The holes are 62mm centres and are 6g self-tapper treads, evident by the metal around the holes being pulled out above the surface. I'll just level them off.
Yes, it's a great tool for the shed. It will get a lot of use. The locking key works really well and easy to operate.
I'm guessing it might have been fitted permanently to a machine of some sort.
It was a good pick up. From memory I think I payed $2 for it.
Similar Threads
-
Help with unknown wood please
By wun4us in forum WOODWORK - GENERALReplies: 4Last Post: 30th May 2011, 08:39 PM -
Unknown Kit
By chrisb691 in forum WOODTURNING - PEN TURNINGReplies: 8Last Post: 23rd April 2011, 02:27 PM -
Unknown tree with an unknown growth.
By Durdge39 in forum TIMBERReplies: 9Last Post: 17th January 2011, 11:38 PM -
unknown species
By Travis Edwards in forum SMALL TIMBER MILLINGReplies: 0Last Post: 7th November 2009, 08:52 PM