Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
7th September 2015, 03:34 PM #1SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Warragul
- Age
- 68
- Posts
- 577
Crosscut sled - adjustable metal runners
I'm about to make my first crosscut sled and also intend on making a mitre crosscut sled but I'm not interested in fiddling about making wooden runners. I've found a few Australian sites that sell metal runners.
Carbatec ... https://www.carbatec.com.au/workshop...mm-18-anodised
Professional woodwork supplies ... http://www.woodworksupplies.com.au/i...e-slider-600mm
Professional woodwork supplies... http://www.woodworksupplies.com.au/s...free-jig-plans
I also like the look of these .... http://www.microjig.com/products/zeroplay/ but no one in Australia stocks them. I could get them from Amazon but that slows the whole process down.
I want them adjustable to get a perfect fit.
Any one used any of these or does anyone have suggestions on others.
-
7th September 2015 03:34 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
7th September 2015, 07:07 PM #2Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,470
Adjustable slides
The last ones on your list from Proffessional Woodwork Supplies are adjustable to get zero play in the channels. I have the same ones on my Incra mitre gauge.
Cheers
-
7th September 2015, 07:30 PM #3
All of those mitre slides are adjustable for fit in the mitre slot.
A bit pricey though.
I use these for sleds https://www.carbatec.com.au/workshop...4-x-24-veritas
One in each slot and I have had good results.Those were the droids I was looking for.
https://autoblastgates.com.au
-
8th September 2015, 11:22 AM #4Senior Member
- Join Date
- Jan 2015
- Location
- Sunshine Coast
- Posts
- 215
I used HDPE. I bought an off cut sheet from a sign maker and simply cut two strips on the table saw. I then used some of it to make the back bed of the cross cut sled from it as well. The sheet I bought cost $25 for a piece that is 1 square metre so I have lots left to make all sorts of other jigs etc from it.
-
8th September 2015, 01:07 PM #5SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Warragul
- Age
- 68
- Posts
- 577
Thanks for the suggestion but I still want adjustable metal runners, even if they're more expensive. The Incra ones look really good. I looked on their web site and they suggest using double sided tape as a temporary join with the top before screwing the runners in. Anyone using these and made their sled that way. Is there a better way?
-
8th September 2015, 07:31 PM #6
Metal runner
Here's a link to the crosscut sled I made. https://books.google.com.au/books?id...20sled&f=false
I fixed the first runner as instructed and used double sided tape for the other. I exchanged the runners for one metal (the first one that is attached) and the other one UHMW. The metal one with adjustable fitting was great. There's a photo of the sled in my Benchcrafted Shaker Bench Build if you want to have a look. I made an additional fence for long parts with the kreg top track that really helped in the bench build (which I still have to finish).
-
11th September 2015, 02:39 PM #7Senior Member
- Join Date
- Oct 2011
- Location
- Frankston, Melbourne
- Age
- 66
- Posts
- 195
I use this one for my sleds
Kreg Jig & Fixture Bar - 30"
you can get them from Carbatec.
-
13th September 2015, 06:04 PM #8
The first carbitec link and the Kreg bar are adjusted from the side of the bar, so the adjustments are always accessible with the sled lifted from the table, but cannot be adjusted in situ.
The Incra ones and the zeroplay are top adjusted, so you either have to have access holes drilled through the sled to adjust them in situ, or work a way to install them inverted so the adjusters are accessible from below once the the sled is raised, again preventing in situ adjustment.
Ideally, if you are using a sled guided by both mitre slots on the table, you would adjust the fit of the first guide, and attach it to the sled then adjust the fit of the second guide in it's slot, apply double side tape and position the part built sled on the table so the tape temporarily locates the second guide. The sled is then raised from the table, inverted, and drilled to accept guide mounting screws. At that point, the second guide can be removed, the DS tape removed, and the guide attached permanently using the predrilled screw holes.I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
14th September 2015, 05:49 PM #9SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Warragul
- Age
- 68
- Posts
- 577
Ordered the incra runners. Would much prefer to adjust them in the slots than outside as mentioned above. I'v also ordered the kreg zero play guides for some smaller jigs. I'll report back when I've used them
Similar Threads
-
Table saw sled runners - what to use
By Arron in forum WOODWORK - GENERALReplies: 20Last Post: 23rd August 2013, 01:59 PM -
Converting troublesome Wooden drawer runners to Metal runners
By DaleBlack in forum WOODWORK - GENERALReplies: 7Last Post: 3rd January 2013, 05:20 PM -
Crosscut sled
By John Samuel in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 11Last Post: 13th October 2012, 04:47 PM -
Crosscut Sled
By Beagle67 in forum HAND TOOLS - POWEREDReplies: 1Last Post: 18th August 2006, 06:30 PM