Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Table saw stuck (nearly)
-
22nd January 2017, 10:03 PM #1Bloke
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 42
Table saw stuck (nearly)
I have a Harvey table saw which apart from one little problem is great. The lowering and raising of the blade has become quite difficult. I removed the top and gave it a clean out got as much sawdust as I could see sprayed some silicon on the trunnion. I didn't want to take anything to bits off cause I'm not the most mechanical person. Replaced everything but improved the problem only slightly.
Someone suggested graphite.
If anyone have any suggestions to improve the movement it would be very much appreciated and thanks in advance.
Marty
-
22nd January 2017 10:03 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd January 2017, 03:33 PM #2GOLD MEMBER
- Join Date
- Nov 2012
- Location
- SE Melb
- Age
- 64
- Posts
- 1,277
I find removing the saw blade gives you a bit more access to the worm gears that are responsible for up and down movement of the blade. Give it a good clean with compressed air and a wire brush. I believe the problem is caused by saw dust being trapped between the gears and gradually being compressed further by winding up and down, forming a hard crust which jams the gears. Once cleaned, you will see the movement coming back. I don't see the need for any lubricants. In fact, it will make things worse if the gears are not completely free of saw dust.
Are you using dust extraction on your table saw?
You may also look to find ways to improve the under table extraction or it will jam again in the future.
-
23rd January 2017, 06:01 PM #3GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Needs to be well cleaned to remove all dust. Graphite powder works wonders.
-
26th January 2017, 12:36 AM #4Senior Member
- Join Date
- May 2016
- Location
- Melbourne
- Posts
- 193
Hey just out of curiosity does the locking screw in the middle of the up/down wheel feel normal when you turn it or is it stiff to move?
-
26th January 2017, 08:45 PM #5SENIOR MEMBER
- Join Date
- Aug 2013
- Location
- Montmorency Victoria
- Posts
- 554
This could be the common problem that has occurred with several Harvey owners .... the problem is in the worm gear rod ens ... hard to explain ...but here goes. Open up the cabinet door on the left (motor) side. You will see a rod for the worm gear that goes from the crank handle to the back of the cabinet. At the back end of the rod there is a round locking ring and a holding bracket. The end of the rod has a large nut. Between the locking rig and the bracket there should be a couple of copper washers. These sometimes get mashed and find there was into the axle part of the holding bracket. You need to clear the copper washer out if caught in the holding bracket and reset the locking ring (need allen key). Regards Rob
Have a look at page 79 in the owner manual (Harvey is the same as Grizzly 0690) The parts are 119 to 122.
Here is the link to the manual http://cdn2.grizzly.com/manuals/g0690_m.pdf
-
26th January 2017, 09:36 PM #6Bloke
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 42
You're dead right Rob. I rang the place where I bought it and he said the same thing. Since my initial question i stripped it again. Loosened that locking ring you mentioned moved it a bit, I think as it was very tight. Gave it another clean, wire brushed the trunnions and blew all the dust I could see. Put everything back and tried it and I think it's about as good as I can get. I can turn the wheel up and down one handed and I think that's a pretty good result.
I also filled as many air holes as I could see to help with the dust extraction. I also stuck some wind stop strip along the the door opening which really sealed quite well. I'll also be having a six monthly clean out and also use the dusty more often. And to be honest I didn't switch the dusty on every time I used it. Ah she'll be right but a few "She'll be rights" amount to a lot of sawdust. It's going into a outside shed soon and a mate is going to set up a remote switch which will make things a bit easier.
Thanks to all for replying it's much appreciated.
Marty
-
27th January 2017, 12:07 AM #7SENIOR MEMBER
- Join Date
- Jul 2009
- Location
- inverloch
- Posts
- 472
I am thinking it is not good idea to seal off all the air holes. you need more available air to replace the air being extracted by the dust collector. On my Laguna Platinum I opened up the cabinet hole from 4" to 6" and cut a hole in the door opposite about 1.5 times as big. the result is that there is absolutely no build up of dust in the bottom of the cabinet.
Similar Threads
-
im stuck where am i
By mick cottam in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 4Last Post: 22nd February 2012, 07:38 AM -
Stuck in a project for a dinning table made of rimu
By frederic76 in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 6Last Post: 8th July 2011, 03:20 PM -
Help! My Triton collet is stuck, and it's not the typical stuck collet!
By old750 in forum TRITON / GMCReplies: 1Last Post: 1st November 2009, 10:03 PM -
Stuck box
By Tiger in forum WOODTURNING - GENERALReplies: 9Last Post: 10th June 2009, 02:56 PM -
Brand New Jointer - Outfeed Table "Stuck"
By jackliveshere in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 12Last Post: 30th September 2008, 03:13 PM