Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
25th October 2009, 02:12 PM #1SENIOR MEMBER
- Join Date
- May 2009
- Location
- Perth
- Posts
- 708
Carbatec Drum Sander - I Found a Better Manual
For those of us with the open end drum sanders such as the generic 16-32 or wds-400 drum sanders from Carbatec, Timbecon etc, there is a much better manual available from Jet for their equivalent sander. See below.
It is vastly superior in terms of providing guidance for:
1. Fitting new sanding strips
2. Aligning the drum
3. How and why to Fine tune the pressure for the guide rollers
I must admit I would have looked at buying the Jet in the first instance but was put off after the last time I went to PTMS in Perth. They are the only JET dealer here and carry very minimal stock levels.
http://content.wmhtoolgroup.com/manuals/man_629004K.pdf
-
25th October 2009 02:12 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
25th October 2009, 09:52 PM #2
Thanks for the link TP1. I have the timbecon version. I found the tool to install the end of the paper interesting. Do you have one of these, didn't get one with my machine.
Squirrel.
-
25th October 2009, 10:03 PM #3
Hi TP1,
Thaks for that. Don't have a drum sander but you never know when the urge might overcome one.
Cheers
Pops
-
26th October 2009, 03:38 AM #4SENIOR MEMBER
- Join Date
- May 2009
- Location
- Perth
- Posts
- 708
No I didn't Squirrel. I think Jet add a few more goodies into their products. However, I am much more confident about what to do now after reading the JET manual. I was originally worried after reading some earlier threads about these sanders, hence my search for a better manual.
-
26th October 2009, 03:48 AM #5SENIOR MEMBER
- Join Date
- May 2009
- Location
- Perth
- Posts
- 708
Hi Pops,
I have been sitting on the fence about this for some time. But I recently had a bad experience with a glue up for a coffee table. It hasn't happened before but this time there was a measurable bow in the centre. I was a bit worried about how perfect I could get the entire surface area after planing/sanding it down, and this was the motivation I needed to take the plunge.
Once I aligned it properly and figured out the do's and don'ts with some test timber, it worked like a charm and my table top is now dead flat!
-
26th October 2009, 05:13 PM #6
Thankyou, thankyou, thankyou... far better than the manual I got with the timbecon unit.
KevI try and do new things twice.. the first time to see if I can do it.. the second time to see if I like it
Kev
-
26th October 2009, 09:38 PM #7SENIOR MEMBER
- Join Date
- May 2009
- Location
- Perth
- Posts
- 708
Similar Threads
-
Carbatec wds-400 drum sander
By justinmcf in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 15Last Post: 3rd March 2011, 11:57 AM -
Big Price Variance at Carbatec for Drum Sander
By TP1 in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 0Last Post: 24th October 2009, 09:34 PM -
Carbatec twin drum sander
By jefferson in forum GENERAL & SMALL MACHINERYReplies: 6Last Post: 7th June 2008, 11:54 PM