Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: making draw side timber
-
31st July 2010, 10:38 AM #1New Member
- Join Date
- Nov 2009
- Location
- victoria
- Posts
- 6
making draw side timber
G'day people need your thoughts on the best way to slot long lengths of pine usually about 2400mm long, slots are 3mmW by 6mmD currently i dock the timber down to short lenghts then run them through my table saw, would a spindle moulder with power feed be suitable for this? i know you can buy draw side timber (allready slotted that is) but to cut a long story short i need to make my own variant thanks
-
31st July 2010 10:38 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
31st July 2010, 11:06 AM #2GOLD MEMBER
- Join Date
- Aug 2004
- Location
- Perth WA
- Posts
- 2,035
As an alternative to your sawbench, by hand using a Router with the appropriate sized bit. The router with it's 150mm dia base will be more in tune with the un-evenness of the timber should it be not quite straight etc.
-
31st July 2010, 11:10 AM #3
I prefer to route the slots in the long lengths of timber first and then cut to length, it's a massive pain to route short lengths unless you have a router table.
cheers
WendyBox Challenge 2011 - Check out the amazing Boxes!
Twist One - Wooden Hinge/Latch/Catch/Handle
Twist Two - Found Object
Twist Three - Anything Goes
-
31st July 2010, 09:21 PM #4Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
A power-fed moulder is great for it, but, unless you plan on doing stacks of it, it's the expensive way
-
1st August 2010, 09:32 AM #5New Member
- Join Date
- Nov 2009
- Location
- victoria
- Posts
- 6
-
1st August 2010, 04:25 PM #6Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
Woodworking Machinery - Sales, Service, Spare Parts & Maintenance
Machines4u - Australia's No.1 Online Machinery Market
I think Ron Mack and H&F have some second hand machines as well
-
2nd August 2010, 12:11 AM #7
Having done it both ways over the years, I dont think you will do it any quicker with a router bit, and even with sideways pressure ie 4 head moulder etc, the inaccuracy throughout long lengths tends to leave you with alot of waste at each end.
Plus the 3mm bits tend to heat up and blunt too fast or breakeverything is something, for a reason:confused:
-
4th August 2010, 10:36 PM #8Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
-
5th August 2010, 01:30 AM #9Senior Member
- Join Date
- Oct 2008
- Location
- fff
- Posts
- 394
An 1/8th blade is 3.1mm. Is this too wide? A table saw with a couple
feather boards seems the simple way, or am I missing something??
I do display boxes and that is how I do it for the back. I do six inch
boards on both edges and rip them down the center and have two
boards..
Read "board" as timber!
-
5th August 2010, 08:49 AM #10New Member
- Join Date
- Nov 2009
- Location
- victoria
- Posts
- 6
Thanks everyone and yes the boards are square dressed i also make display boxes (re Papa) it was a small deal at the start but now i'm doing loads of them, i have always used my table saw for this but the numbers of peices i'm putting through now are just to much to do manually my background is in building not cabinet making so i'm not up with the diferent techniques and machinery to get the results i'm after all your help is greatly apprieciated.
-
5th August 2010, 11:08 AM #11Senior Member
- Join Date
- Oct 2008
- Location
- fff
- Posts
- 394
I am running eight foot boards and then cutting them to length.
It makes sixteen feet of stock with three cuts.
Similar Threads
-
timber with at least one side natural (uncut)
By ronnie in forum TIMBERReplies: 3Last Post: 30th August 2003, 04:24 PM