Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 3 of 3
  1. 8th November 2015, 12:05 AM #1
    hellofellow
    hellofellow is offline Senior Member
    Join Date
    Oct 2013
    Location
    East Ballina
    Posts
    195

    Default New jointer blades

    Hi again everyone,

    Have been doing a real makeover on the workshop.

    I have a 6inch Delta 37-190 jointer. I bought this secondhand a while back but have not got a whole lot of use out of it as I never took the time to set it up properly. Well that has changed today and I am trying to get her working like new...

    I want to buy some new blades, now this is my first jointer so forgive the ignorance- will any 6inch blade fit any 6 inch jointer?

    Ie I can pick up the correct blades off amazon for approx $100 AU
    http://www.amazon.com/37-658-Knives-.../dp/B00002238E

    Or carbatec 6 inch blades for $39--
    https://www.carbatec.com.au/blades/p...ize-155x12x3mm

    Id much prefer to buy the 40$ aftermarket blades but was unsure if they would fit?!

    Kind Regards,

    Andrew






    /
    Reply With Quote Reply With Quote
  2. 8th November 2015 12:05 AM # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. 8th November 2015, 07:29 AM #2
    Chief Tiff's Avatar
    Chief Tiff
    Chief Tiff is online now Butcher of wood
    Join Date
    Jun 2010
    Location
    Bundaberg
    Age
    54
    Posts
    3,429

    Default

    The Carbatec ones should fit ok, just pull out one of the Jet blades and measure it. If it has any funny indents or holes that are required for bolting it down then you'll have to go with the OEM but pretty much all 6" jointer take basic blades roughly 1/2" wide, 6" long and 1/8" thick.
    Reply With Quote Reply With Quote
  4. 8th November 2015, 07:38 AM #3
    Jeffen
    Jeffen is online now SENIOR MEMBER
    Join Date
    Sep 2011
    Location
    Hervey Bay
    Posts
    250

    Default

    Hi Andrew,

    why not have the old one's sharpened?
    Should cost about $10-15 total at your local saw sharpening service.

    Regards, Jeff
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. sharpening jointer blades
    By gtseraf in forum GENERAL & SMALL MACHINERY
    Replies: 3
    Last Post: 24th December 2013, 03:33 PM
  2. Jointer Blades
    By Ranger in forum JOINTERS, MOULDERS, THICKNESSERS, ETC
    Replies: 1
    Last Post: 31st May 2008, 05:14 PM
  3. Jointer Blades
    By Packrat Pete in forum HAND TOOLS - POWERED
    Replies: 3
    Last Post: 13th October 2006, 05:41 PM
  4. Jointer blades
    By ozwinner in forum JOINTERS, MOULDERS, THICKNESSERS, ETC
    Replies: 1
    Last Post: 4th March 2004, 04:53 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules