Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Steel plate for welding table
-
14th August 2014, 11:53 AM #1Banned
- Join Date
- Apr 2013
- Location
- adelaide
- Posts
- 295
Steel plate for welding table
My welding table has a stainless top; however, it is too small (600mm x 600mm) so I intend on making a larger table. Any ideas on where to get (cheap) 12mm + scrap plate in Adelaide, around a metre square, give or take? I intend on bracing the underneath of the plate to prevent distortion as on my current S/S plate so 12 mm plate shouldn't be a problem.
-
14th August 2014 11:53 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th August 2014, 03:32 PM #2GOLD MEMBER
- Join Date
- Sep 2010
- Location
- Lebrina
- Posts
- 1,099
Gee, 1000 X 1000 X 12 plate couldn't really be called scrap.
I reckon you may nearly need to approach a steel retailer or fabricator and get a piece ripped off a plate, possibly even a 500 X 1800 or 500 X 2400 piece that you then turn into a 900 X 1000 or 1000 X 1200 piece.
-
17th August 2014, 04:09 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,793
Since I retired last year I have done a scrap steel "milk run" around a few salvage yards and steel suppliers about every month. The biggest piece of scrap 12mm plate I have found has been some circular pates about 450 mm in diameter. I did find a 2400 x 1200 piece of 3/4" thick plate that was advertised on gumtree for $150 and thought that would make a great bench top until I found out it was used as construction road way plate so it was buckled well beyond that sort of use.
-
17th August 2014, 10:29 PM #4
-
17th August 2014, 11:46 PM #5Banned
- Join Date
- Apr 2013
- Location
- adelaide
- Posts
- 295
Sims.
I used to get all my steel from Sims in Spearwood before I moved east in 2006. They had loads of second hand steel and plate of pretty well any size you wanted. Good prices also.
-
18th August 2014, 12:18 AM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,793
-
18th August 2014, 09:18 AM #7
I made my welding table with two parallel flanges C channel 380x100x900, well over 100K
I bolted them together with 19mm bolts and tack weld them from below and to the steel frame. Way over engineered but at the time ... 25 years ago, I worked with BHP in their wiremill and scrap steel was plentiful...
Jeee, 25 years ago ... remind me of that line at the end of the expendables when Silvester Stllone gets his Grumman Albatross back. -"That belongs in a museum" ... and the reply: -We all do!
ha ha“We often contradict an opinion for no other reason
than that we do not like the tone in which it is expressed.”
Friedrich Nietzsche
Similar Threads
-
Advice on welding thin steel plate
By Sterob in forum WELDINGReplies: 24Last Post: 31st July 2012, 06:57 PM -
Flattening a steel plate
By WelderMick in forum METALWORK FORUMReplies: 17Last Post: 2nd June 2010, 10:21 PM -
Welding Works in Solar Flat Plate Collector
By ndr in forum WELDINGReplies: 1Last Post: 24th October 2008, 09:29 PM