Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Dry Scarf Joints
-
12th May 2011, 06:46 PM #1Novice
- Join Date
- Apr 2010
- Location
- Brisbane
- Posts
- 11
Dry Scarf Joints
Hi Guys,
I need some experienced advice.
I Had some trouble with my firth scarf joint. About 6 inches of the join has come apart. The edges are covered with with epoxy, and there are some small blobs of glue (about 1/8 inch round) so it appears my glue might have been too runny or I might have used too much pressure.
I coated the end grain with two coats on epoxy then mixed up some glue and brushed it on. Now I'm wondering;
How much filler by volume should be used (approximately) for glue.
Can glue and filleting paste be used on bare ply and timber without an initial coat of epoxy. (not end grain)
-
12th May 2011 06:46 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
12th May 2011, 09:18 PM #2Senior Member
- Join Date
- Mar 2010
- Location
- Queenstown New Zealand
- Posts
- 382
Hi Jethro, do you have a picture or two of the bad joint?
Ian
-
12th May 2011, 09:31 PM #3Novice
- Join Date
- Apr 2010
- Location
- Brisbane
- Posts
- 11
No sorry Ian,
I can see that each face of the scarf is shiny and covered in clear epoxy, whereas the rougher marks have the white colouring of the glue mix.
I'm now tossing up whether to finish off with use butt joints, fibreglass joints or a bailing bucket.
Regards
Geoff
-
12th May 2011, 11:38 PM #4Dave
StorerBoat Builder, Sailor, Enthusiast
Dave's GIS Chronicles | Dave's Lugs'l Chronicles | Dave's StorerBoat Forum Thread
-
13th May 2011, 12:03 AM #5Member
- Join Date
- Apr 2010
- Location
- Oklahoma USA
- Posts
- 90
When mixing epoxy I use translucent drinking cups. After mixing the epoxy I add silica, while looking through the side of the cup, to a point that doubles the depth. If there's an inch of epoxy in the cup I sprinkle an inch of silica on top of it. That gets close to the consistency I want then I add a bit more if needed.
I wouldn't use thickened epoxy in a joint without saturating the wood with the thin stuff first.
Your description sounds like a starved joint. Some things that can cause that are not saturating the wood well with thin epoxy before applying the thickened stuff, too much clamping pressure, not enough glue, glue running out of the joint, and squeezing the glue out of the joint then easing clamping pressure.
-
13th May 2011, 09:39 AM #6Senior Member
- Join Date
- Mar 2010
- Location
- Queenstown New Zealand
- Posts
- 382
Is this bad scarf joint joining ply sheets, spars, chine logs, gunwales or what? Is it possible to saw it apart and re-do it? I think that would be the best option if at all possible.
Ian
-
13th May 2011, 09:56 AM #7
I think mixing thickeners by volume will be too difficult. Some say peanut butter consistency, but not all peanut butters are the same. A good mixture is one that will peak and then slump down slowly. If it holds a peak, then that is too thick, but is right for filleting.
I had the same thing happen on my original boom, which broke. On close inspect, the break started when the scarf joint failed. It is important to coat both surfaces of a scarf joint with unthickened epoxy first, and then apply plenty of the thickened epoxy over that. Too much pressure causes a dry joint, so that is likely what has happened to your joint.
Instead of pulling it apart, is it practical for you to add a butt strap?
-
13th May 2011, 10:30 AM #8Novice
- Join Date
- Apr 2010
- Location
- Brisbane
- Posts
- 11
Thanks guys,
I was joining two 8" sheets of ply, and will try again with some new found knowledge.
Originally I coated each surface with thin epoxy, then mixed the glue, however from your replies it would appear that I made the glue too thin and from memory I put a lot of initial pressure on that edge and then held it down with less pressure.
Now back to the shed.
Regards
Geoff
-
13th May 2011, 08:13 PM #9Novice
- Join Date
- Apr 2010
- Location
- Brisbane
- Posts
- 11
Back to the shed,
This time I mixed up a much thicker glue and it didn't self level as much as the last mix so hopefully things will work out fine this time.
I'll let you know tomorrow.
Regards
Geoff
-
13th May 2011, 09:33 PM #10
With epoxy, you only need enough clamping pressure to bring the two pieces in contact with the goo, that's it.
Wetting out raw wood prevents the dry wood from sucking out the resin and leaving you with only filler powders in the joint. A simple wet out and wait is the usual approach. If the raw wood looks like it might want more to "drink" apply some more, but in most cases the initial wet out is sufficient, before applying a thickened coat.
The viscosity of thickened epoxy is dependent on many things. The rule is, no thicker then you need. On vertical and over head surfaces, you'll need a non-sagging mix, which is a heavy peanut butter consistency. The pulled up peaks remain as you mix. Most adhesive mixtures don't need to be this thick and a heavy cream consistency is all you need. This will "slump and sag" when you pull up a peak during mixing, but inside a joint will remain in place from the friction of the joining pieces.
How much, well it depends on temperature, humidity, your in laws mind set and the color of your hair. There are so many variables, that precise mixtures can't be offered, except in environmentally controlled conditions.
-
14th May 2011, 09:38 AM #11
As I often find myself saying ... you guys are really good!
MIK
Similar Threads
-
Scarf joints
By IWieldTheSpade in forum MUSICAL INSTRUMENTSReplies: 26Last Post: 17th June 2010, 02:23 PM -
Which way to scarf?
By Gascat in forum MUSICAL INSTRUMENTSReplies: 33Last Post: 12th February 2010, 12:06 PM -
gluing scarf joints.....
By Andrew_B in forum MUSICAL INSTRUMENTSReplies: 16Last Post: 6th January 2010, 03:30 AM -
Veneer Glues and Scarf Joints
By stevec1234 in forum WOODWORK - GENERALReplies: 2Last Post: 12th January 2009, 08:39 AM