Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 40 of 40
Thread: Another GIS build in OZ
-
13th December 2013, 10:22 PM #31Intermediate Member
- Join Date
- Mar 2008
- Location
- Melbourne
- Posts
- 32
Dave, yes how to do with any of the items you wish to "customise". I don't know about you, it's only when I have finished doing something, I come up with an even better solution than the one completed. Here is the final detail of where the capping meets the seat. The capping is just a piece of 6mm ply with an edging of merbue left over from a decking project.
goat-175.jpggoat-172.jpg
If I was doing it again, I think I would have one rather than two pieces of timber for the middle seat supports. Then where the capping meets the seat it would not look added on. Hindsight is a wonderfull thing.
Another small detail I changed is the front deck. I extended it to the rear face of the stiffening supports on bulkhead 2. Glued another piece of merbue on the edge. My thinking for this was to make a lip so any water coming from the deck will bypass my hatch.
goat-173.jpggoat-174.jpg
No doubt, after a few hours in use I will discover,
A/ the overhang is not enough
B/ no overhang is needed at all
or C/ some sort of tripping hazard.
Good idea??? We shall see.
cheers Trevor D.
-
13th December 2013 10:22 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th December 2013, 07:08 AM #32Member
- Join Date
- Jul 2013
- Location
- NH
- Posts
- 77
You and I detailed the seats very similarly. I thought the same thing about the middle seat support after installing the cap on the center case. Looks nice though!
-
21st March 2014, 01:58 AM #33Intermediate Member
- Join Date
- Mar 2008
- Location
- Melbourne
- Posts
- 32
Wow, I have been very slack in keeping the build updated. Here is the next bit that I finished before Christmas.
Handling large bits of ply or long bendy pieces of timber with epoxy on them I find challenging without helpers. The rewarding part however is working out some way to put the bits together without dropping on dirt floor or accidentally smearing epoxy on places that are not supposed to get it. I was quite pleased with my solution for the inwhales.
goat-179.jpg
I clamped the timber in rough position, but with a spacer so I could apply glue.
goat-181 1.jpggoat-180.jpg
Each end also had a spacer, but not clamped to the boat. The weights at the bow and the clamp jaw at the stern are keeping the timber bent downwards.
goat-183.jpg
Piece in place with epoxy applied. Starting at the centre I removed the spacer, maneuvered inwhale and put clamps in place.
goat-176.jpg
One side at a time. I surprized myself that it worked ok.
cheers Trevor D
-
26th March 2014, 09:45 AM #34Intermediate Member
- Join Date
- Mar 2008
- Location
- Melbourne
- Posts
- 32
Measure twice, cut once. Nothing wrong with my measuring, just chose the wrong mark to cut to.
goat-184.jpg
Port side at the stern. Two marks, cut made at the correct one.
goat-185.jpg
Starboard side at stern. Two marks, cut made at the wrong one. Grrrr. Clearer marks would I'm sure, help the brain focus.
4080-002.jpg
Time to get the mind away for a while. My favourite spot to go sailing. Gippsland lakes, Victoria. About 3 1/2 hours drive from home.
4080-004.jpg
We were holed up at this jetty for two nights escaping the wind.
4080-008.jpg
It doesn't look too bad from this pic, but there was no way I was venturing into that when 200 meters away, around the point,
4080-015.jpg
we could watch the swans. Yes our swans really are black.
4080-019.jpg
Well after the blow we had a perfect sailing day ending up here.
4080-021.jpg
Unfortunately the wind returned, so resulted in another two nights without untying . I appreciate everyone else sharing a bit of what things are like where the sail, so hope others feel the same way. Maybe not the amount of sailing I was hoping for, but still most relaxing.
cheers Trevor D
-
28th March 2014, 08:58 PM #35Intermediate Member
- Join Date
- Mar 2008
- Location
- Melbourne
- Posts
- 32
Getting close to the completion.
goat-189.jpggoat-188.jpg
goat-190.jpg
At this point, in the middle of all this wet sanding I finally was very happy about having a dirt floor.
goat-191.jpg
First coat of hull paint. I am using the water based Aquacoat. I ended up doing three coats, as after two it was not quite even.
Cheers Trevor D
-
2nd April 2014, 04:12 PM #36Intermediate Member
- Join Date
- Mar 2008
- Location
- Melbourne
- Posts
- 32
In keeping with the philosophy of keeping this build as cheap as reasonably possible I got a free trailer. It was a project a friend was doing for a Pacer dinghy, but never got finished. He gave it away because he was moving to another house and had to get rid of clutter in a hurry. Sometimes we get lucky. With a bit of modification I'm hoping it will be perfect for the Goat.
goat-194.jpggoat-193.jpggoat-195.jpg
In the meantime I got a bit impatient. Boat ready, sails on but no trailer.
goat-198.jpggoat-197.jpg
Hmmm..... thinks to self......It might be worth a try........after all it's not very far.....
goat-200.jpg
So I quickly hitched the beach trolley onto the back of the car, travelled about 60 metres on public roads, (I looked both ways and made sure there was no other traffic) and went next door for a maiden launch.
goat-201.jpggoat-203.jpggoat-216.jpggoat-213.jpggoat-207.jpg
The dam is about 50 metres wide, just enough to get the sail working. I went back and forth with a very large grin on my face. As others have reported acceleration is surprisingly quick, even with the gentle puffs.
goat-229.jpggoat-223.jpg
Had to try out the oars as well. Made from Miks plans.
Very happy man, now back to that trailer.
Cheers Trevor D
-
2nd April 2014, 06:05 PM #37Senior Member
- Join Date
- Sep 2011
- Location
- Gothenburg, Sweden
- Posts
- 100
Congratulations!
The Goat looks really nice and seeing you sail in that small dam put a smile on my face as well.
Pontus
-
2nd April 2014, 11:45 PM #38Senior Member
- Join Date
- Feb 2013
- Location
- New London, Minnesota
- Posts
- 181
Congratulations. The Goat looks terrific and confirms the color scheme I have been thinking of all along. It also introduces my next project - beach trolley.
-
3rd April 2014, 02:00 AM #39Intermediate Member
- Join Date
- Mar 2008
- Location
- Melbourne
- Posts
- 32
Pontus, Northstar, thank you. I would have preferred to have the spars and mast bright finished, but the second hand timber was a bit too discoloured, so went with paint. The choice of colour was determined when the local seller of nautical supplies had a litre of oldish International Brightsides, grey, in the bargain bin for $20. "Hmmm......yep,,, that's a good colour.
I am hoping the beach trolley works out. The thing I am looking forward to is with the boat and trolley off I can use the flat bed trailer for other tasks. I am planning to extend the draw bar 700 mm, so the boat will then be 200 mm sticking out beyond the rear of the trailer. I will be getting a local trailer manufacturer to do that. Seems the safe smart way to go.
Cheers Trevor D
-
4th April 2014, 02:32 AM #40
ker-SPLASH!!!
Woo hoo!!! You're gonna need a bigger pond now. Enjoy...Dave
StorerBoat Builder, Sailor, Enthusiast
Dave's GIS Chronicles | Dave's Lugs'l Chronicles | Dave's StorerBoat Forum Thread
Similar Threads
-
Build #3
By cagsy in forum MUSICAL INSTRUMENTSReplies: 8Last Post: 26th February 2012, 10:28 PM -
help me build a basic flat build bed trailer for my kayaks
By gros21 in forum TRAILERS & OTHER FABRICATED STUFFReplies: 7Last Post: 13th October 2011, 08:47 AM -
To buy or build
By jpo in forum THE WORK BENCHReplies: 0Last Post: 10th November 2010, 06:30 PM -
Trailer - to build or not to build
By motegi in forum TRAILERS & OTHER FABRICATED STUFFReplies: 17Last Post: 6th May 2009, 03:07 PM