Picture(s) thanks: 0
Results 16 to 26 of 26
-
27th September 2016, 11:01 PM #16Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
And again...because apparently people don't think I have enough work to do...
80mm diameter planing bit vs. 3200x190x80mm American Oak; one end fell off the table sending the other end up into the tool
Fortunately, the only damage was the broken stud on the tool holder and the 4 carbide inserts on the tool, I was very worried that the spindle would be pushed out of alignment and that's definitely beyond my pay grade
-
27th September 2016 11:01 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
27th September 2016, 11:09 PM #17GOLD MEMBER
- Join Date
- Oct 2014
- Location
- Caroline Springs, VIC
- Posts
- 1,645
Dont forget Elan, CNC makes life easier and stress free. I bet it doesnt seem like it
-
27th September 2016, 11:35 PM #18Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
As long as I'm not the one who breaks it I don't mind so much, I quite like pulling things apart
-
28th September 2016, 10:53 AM #19
-
28th September 2016, 11:06 AM #20Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
The vacuum does nothing if there's even the slightest bit of space, I'm not sure if you've ever tried to flex a piece of timber of that section but it isn't going anywhere in a hurry.
We ended up screwing two boards to the timber so the vacuum had something to hold
-
28th September 2016, 01:16 PM #21
I understand that a board that thick is not very flexible, but I remain curious about the relative speed and waste of flattening and dimensioning on the CNC vs using a jointer and thicknesser
regards from Alberta, Canada
ian
-
28th September 2016, 01:26 PM #22Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
The main advantage is not having to manually handle 40+kg boards. We only did one face on the CNC, then thicknesser, then an edge on the panel saw, then thicknesser to width. The finished thickness was 62mm, so the waste was going to happen anyway
-
28th September 2016, 02:05 PM #23
Out of interest, what are you making that needs a board 170(?) x 62, 3.2 m long
regards from Alberta, Canada
ian
-
28th September 2016, 02:20 PM #24Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
A 3000x1200x60mm dining table
-
28th September 2016, 03:02 PM #25
I know someone in Melbourne who can sell you a small crane to move that monster into place
regards from Alberta, Canada
ian
-
28th September 2016, 04:14 PM #26Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
Fortunately we didn't deliver it, but it wasn't too bad with one of us on each corner
Similar Threads
-
Is my torch installed properly
By gtr fan in forum WELDINGReplies: 9Last Post: 7th June 2011, 06:37 AM -
Collet not holding bit properly?
By RichardL in forum ROUTING FORUMReplies: 12Last Post: 28th September 2007, 09:45 PM -
Too old to remember properly
By Bob Willson in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 24Last Post: 11th September 2004, 07:56 PM