Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: 3M 7907S Full face mask
-
23rd November 2017, 12:05 PM #1SENIOR MEMBER
- Join Date
- May 2013
- Location
- Auckland, New Zealand
- Posts
- 997
3M 7907S Full face mask
I have been using 3M 7500 series mask for the past 2+ years.
In late October the plastic back strap finally broke and I cant get a replacement, therefore I decided to go full face to protect my eyes as well.
In NZ for Full Face 3M mask you can only get the 6800/6900 series from the safety shops, to get anything else ordered from the shops it will take about 2-3 months, 6800/6900 has 4 harness, 7800/7907s has 6 harness.
Based on the reviews I've read online, I decided to go with the 6 harness and bought it through one of the more reputable internet based retailer, a few weeks later the mask arrived.
I have not used the 4 harness system but after using my new mask for a few weeks, I must say, they didnt invent 6 harness for no reason.
as for heat/fogging - no issues with my new mask. it vents well and has speech diaphram, each time I use my mask it is between 2 - 3 hours. maybe because AKL is not too hot?
7907s comes in 1 size only. I was a bit worried because I have a very large head(circumference 63cm+/- 2cm) due to a medication condition I had when I was a child, but I worried too much. the 7907 fitted very well and has spare room for larger head.
possible improvement?
1. Cost. the 7907s costed $300 USD at the time of purchase. you cant put a price on your lung but $300 is a lot compare to the 7500 series, which is about $35 USD.
2. Need to vacuum my head before I take off the mask.
A side note, the 7907S is made in Japan.SCM L'Invincibile si X, SCM L'Invincibile S7, SCM TI 145EP, SCM Sandya Win 630, Masterwood OMB1V, Meber 600, Delta RJ42, Nederman S750, Chicago Pneumatics CPRS10500, Ceccato CDX12
-
23rd November 2017 12:05 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd November 2017, 05:18 PM #2
-
28th November 2017, 10:04 AM #3SENIOR MEMBER
- Join Date
- May 2013
- Location
- Auckland, New Zealand
- Posts
- 997
IMG_1437.jpg
here is a photo of the mask arriving.
I wont post the photo of me fitting it - you guys dont need to see me half naked do you
It has been quite hot in AKL and I get more sweat from my earmuff than the 7907s.
The ear muffler I use is a Leightning L0F.SCM L'Invincibile si X, SCM L'Invincibile S7, SCM TI 145EP, SCM Sandya Win 630, Masterwood OMB1V, Meber 600, Delta RJ42, Nederman S750, Chicago Pneumatics CPRS10500, Ceccato CDX12
-
28th November 2017, 03:14 PM #4GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,268
What about wearing glasses with it?
Mick.
-
29th November 2017, 07:58 AM #5SENIOR MEMBER
- Join Date
- May 2013
- Location
- Auckland, New Zealand
- Posts
- 997
Hi Mick, unfortunately you cant wear glasses with this mask...
SCM L'Invincibile si X, SCM L'Invincibile S7, SCM TI 145EP, SCM Sandya Win 630, Masterwood OMB1V, Meber 600, Delta RJ42, Nederman S750, Chicago Pneumatics CPRS10500, Ceccato CDX12
Similar Threads
-
powered respirator, full face or 1/2 face??
By old_picker in forum HAND TOOLS - POWEREDReplies: 7Last Post: 13th December 2008, 09:58 AM -
Face mask respirators
By andrewsd in forum WOODTURNING - GENERALReplies: 0Last Post: 1st March 2007, 05:01 PM -
lathe face mask
By JDarvall in forum SAFETYReplies: 24Last Post: 11th January 2006, 11:34 PM -
Condensation on face mask
By Rowan in forum WOODTURNING - GENERALReplies: 13Last Post: 24th May 2005, 09:19 AM -
Face Mask!
By John Saxton in forum FINISHINGReplies: 20Last Post: 2nd September 2000, 06:36 PM