Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Stanley number 1
-
1st February 2024, 11:15 PM #1
Stanley number 1
I recently brought a turn of the century Stanley number 1 bench plane.
The plane is missing its tote, plus it's mounting stud and nut.
I plan to make a new tote and stud, I was able to find the external dimensions of the two things from the following site however there is no mention of the stud thread and without the stud I don't have a tote hole angle.
Stanley Number 1 Hand Plane Dimensions
I'm hoping someone can tell me what thread pitch was used and the stud mounting angle.
Thank you MarkI've become a tool of my tools.
-
1st February 2024 11:15 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
2nd February 2024, 07:46 AM #2GOLD MEMBER
- Join Date
- Oct 2018
- Location
- Dandenong Ranges
- Posts
- 1,893
Hi there. I have used 6" bullet head nails (they are the right diameter) and 12/20 die to make replacement studs for my Stanley hand planes. Once you make the stud you can measure the angle.
-
2nd February 2024, 10:49 AM #3
Just a thought.
Have you tried a stud from a #3 or #4 to see if they are the same thread?
If they are that would give you the angle and the need to thread only one end after shortening.
H.Jimcracks for the rich and/or wealthy. (aka GKB '88)
-
2nd February 2024, 11:21 AM #4
-
2nd February 2024, 08:04 PM #5
Thank you for your replies.
The studs on the larger planes are not a match, they are much larger 12-20.
The No 1's stud is 7/64" so far I have not been able to cut a thread to test on the plane.
MarkI've become a tool of my tools.
-
3rd February 2024, 09:23 AM #6GOLD MEMBER
- Join Date
- Oct 2018
- Location
- Dandenong Ranges
- Posts
- 1,893
Thanks Mark. I only have experience with #3 - #7. Knowing what I do about the #1 (which is very little), I am not surprised that things are scaled down.
-
6th February 2024, 12:33 AM #7
No 1 tote thread.
I tried a number of threads until I found the one that worked.
8-32 and it is angled at 22 degrees.
Thanks again MarkI've become a tool of my tools.
Similar Threads
-
DONE: Stanley number 3
By riverbuilder in forum WANTED & WANTED TO BUY - in AustraliaReplies: 14Last Post: 28th July 2021, 06:34 PM -
SOLD: Stanley Long Jointer Hand Planes Number 31 and Number 32
By Scribbly Gum in forum WOODWORK - Tools & MachineryReplies: 4Last Post: 13th May 2021, 11:27 PM -
A.C.T. English Stanley Number 10
By Thumbthumper in forum WOODWORK - Tools & MachineryReplies: 2Last Post: 26th August 2018, 09:31 AM -
A.C.T. English Stanley number 6
By Thumbthumper in forum WOODWORK - Tools & MachineryReplies: 6Last Post: 17th November 2017, 07:13 PM -
stanley number 10 rabbet
By Shedhand in forum HAND TOOLS - UNPOWEREDReplies: 13Last Post: 28th February 2007, 10:42 PM