Results 736 to 750 of 950
-
29th January 2016, 08:07 PM #736GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
Kevin,
Glad you were able to walk away after your fall.
Thanks for the information. I will be looking at the potential of adding the running boards on my loco. Will depend on accessibility to adding the different components and attachment points. Am a bit wary that it may hide too much of my wheel and brake assemblies ???
Regards
Keith
-
29th January 2016 08:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
30th January 2016, 04:16 PM #737
I would leave the shunters' boards off. They were installed so shunters could safely ride on the side of the engine without getting cleaned up by connecting and coupling rods. Why hide the details you have taken the time to include?
(Running Board would probably refer to the narrow ledge around the outside of the tank, or wider plating beside the boiler on tender engines. eg the K class has a running board which can be accessed from the door on the fireman's side of the cab.)
-
31st January 2016, 01:02 AM #738
Loco is looking great Keith!
Bret
-
31st January 2016, 08:15 AM #739GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
-
31st January 2016, 04:48 PM #740GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
Hi All,
Today I fitted the horizontal cabin handrails and also the handles at the front of the cabin just beside each of the windows. The photos show the 268 number and the reason that I decided to make the side handrails in 2 pieces instead of one so that I wouldn't impact on the numbers. The front view also shows the D4 loco type lettering in position.
I have now started on the rear wall of the cabin which will then enable me to commence work on the coal bunker.
Regards
Keith
number and rails2.jpg number and rails1.jpg
-
31st January 2016, 05:43 PM #741
Looking Good. I think you made the right choice to leave a gap for the side number plate.
I always thought the sub class was written as superscript, but the D4 has both! Subscript on the front, Superscript on the bunker. If you had not made the class plate so clear I would not have picked that up.
-
31st January 2016, 07:12 PM #742GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
Hi Kevin,
I have mucked up for the bunker. Both my D4 plates are the same. I didn't notice the difference until you pointed it out. My other plate is the same as the front. The rear will be the same as the front.
Have attached a photo of the original prototype for others to see.
Regards
Keith
Loco type.jpg
-
2nd February 2016, 04:42 PM #743GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
Hi All,
Been doing a bit of work on the rear of the cabin. Need to get this work done before I can start on the coal bunker. There is a sliding door in the middle. (This has been welded up in the original locomotive) I reckon the fireman would know what that is for.
There will be a pivoted "steel" lid on the top of this addition.
The bars on the windows have been made out of 3mm wire. There are lots of rivets in this section of the locomotive - I have use spiral nail heads.
I used the internal cabin light for light for the photo.
Regards
Keith
rear of cabin progress.jpg
-
2nd February 2016, 04:51 PM #744
That is one top photo Keith, and the detail looks fantastic, sir....Cheers, crowie
Last edited by Big Shed; 2nd February 2016 at 04:56 PM. Reason: Please refrain from quoting slabs of text and photos
-
2nd February 2016, 05:23 PM #745
Kool Bananas Charlie!.
Cheers
Trev.
-
2nd February 2016, 07:14 PM #746
Once more you have me riveted by your attention to detail.
As you are aware, the rear cab wall has had some patches welded in. I am not sure it these were openings to store oil feeders, or part of the tank (under the bunker) that has rusted out. With the lids at the top, again I am not sure if they were to access the bunker to aid trimming or for storage.
Compared to what I am used to, the coal chute is up high so I am sure a lot of fuel would have spilled onto the floor to be cleaned up and shoveled onto the fire.
-
2nd February 2016, 09:59 PM #747GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
-
3rd February 2016, 07:42 AM #748Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
This has been greatly informative and entertaining Keith! I envy your patience!!
-
3rd February 2016, 04:29 PM #749GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,422
Hi All,
I'm pretty happy how the rear of the cabin is coming up. I cheated with the hinges - I used 12mm jewellery box hinges. The upright section of the hinge still hasn't been secured to the wall. The good thing is that the hinges on the real loco have been welded into position. Using 5 minute araldite - it looks like a weld after the primer has been applied (albeit - maybe a rough weld).
The handle bearing is made of pine. The shaft turned out of aluminium. The handle itself is 4mm mild steel rod. There are narrow side walls still to be added.
It really is an eye opener on how little space the crew had to carry out very manual work.
Regards
Keith
cabin rear wall.jpg
-
3rd February 2016, 07:51 PM #750
Two is company, three is a crowd. No room to take rail fans or loved ones (not that they would be allowed any way). When you have a look at a couple of images of the class at work it appears as if there is some sort of door to stop the crew from accidentally falling out (or to stop the shunter or guard from getting cozy in the cab).
Keith, I always enjoy watching the engine come together as I am sure many others do. With some careful placement inside or outside your workshop, you would think the engine is at a quiet country town, except in your last image there is a giant chair in the background.
Similar Threads
-
Manual Training for Common Schools - 1910
By pmcgee in forum HAND TOOLS - UNPOWEREDReplies: 4Last Post: 25th January 2014, 07:20 PM -
Window frame timber 1910
By GTHO in forum TIMBERReplies: 7Last Post: 14th September 2009, 09:55 PM -
Toy locomotive
By Andy Mac in forum WOODWORK PICSReplies: 13Last Post: 27th January 2007, 09:48 AM