Thanks Thanks:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 6 of 6
  1. #1
    Join Date
    Jul 1999
    Location
    Glen Iris, Vic, Australia
    Posts
    2,196

    Default Find the centre of any circle. (Grrrrr. Found this 1 hour after I needed it.)

    Skill Builder: How to Find the Center of Any Circle


    A comment of the save article I how I did it:

    poppy ann • a year ago
    it's just as easy to use a ruler just measure across the circle moving the ruler until you get the maximum distance between the two places the ruler crosses the circle and draw a line across (or draw a small line around the centre position) move approximately 90 degrees (does not matter if it is not exactly 90 deg) and use the rule to get the maximum size again and draw a line and where the two lines cross that is the centre."
    Thanks,
    Barry G. Sumpter
    May Yesterdays Tears Quench the Thirst for Tomorrows Revenge

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    63
    Posts
    13,354

    Default

    I made a jig to find the centres of log blanks for turning, which is used pretty much in the manner you describe with a bit more convenience.

    It works just as well for finding the centres of circles marked on flatwork.
    Attached Images Attached Images
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  4. #3
    Join Date
    Feb 2003
    Location
    back in Alberta for a while
    Age
    68
    Posts
    12,006

    Default

    Quote Originally Posted by barrysumpter View Post
    Skill Builder: How to Find the Center of Any Circle


    A comment of the save article I how I did it:

    poppy ann • a year ago
    it's just as easy to use a ruler just measure across the circle moving the ruler until you get the maximum distance between the two places the ruler crosses the circle and draw a line across (or draw a small line around the centre position) move approximately 90 degrees (does not matter if it is not exactly 90 deg) and use the rule to get the maximum size again and draw a line and where the two lines cross that is the centre."
    bah humbug

    if it's a true circle, draw two chords approximately 90 degrees to each other, bisect both cords, the exact center is where the bisection lines cross.
    regards from Alberta, Canada

    ian

  5. #4
    Join Date
    Jun 2010
    Location
    Bundaberg
    Age
    54
    Posts
    3,402

    Default

    Alternatively, draw two pairs of tangents where each pair cross each other. Bisect the included angle of each pair and where these lines cross is the centre.

    This is the principle behind Skew's jig; in his case it can also be used as a square but as a centre finder the 90° is unnecessary; so long as the middle bit is exactly at half the angle of the sides it will work.
    Nothing succeeds like a budgie without a beak.

  6. #5
    Join Date
    May 2008
    Location
    BELL POST HILL, 3215
    Age
    87
    Posts
    2,332

    Default The Centre.

    Hi All,
    I do mine a little differently as I have made 3 out of Clear Acrylic in a circle.
    Found the approx. centre, drilled a small hole, took to it with the Dividers, & scratched circles aprox. 20mm. apart. Then used a Black White Board Marker, drew on the lines, one at a time then wiped the excess off, & now have a clear black line.
    Centre hole made a touch bigger, lay it over your wood to the best circle & punch the centre.
    Regards,
    issatree.
    Have Lathe, Wood Travel.

  7. #6
    Join Date
    Oct 2006
    Location
    Tallahassee FL USA
    Age
    82
    Posts
    4,650

    Default

    The "easy" method of the OP's link is actually harder than needed. The second step doesn't need to align with one of the first edges. The two positions of the framing square can be placed almost anywhere.

    In any right triangle, the hypotenuse lies on a diameter of the circumscribed circle. With the corner of the framing square on the perimeter, scribe the edges and connect the two crossings to form a hypotenuse. Do it again someplace else. Where the hypotenuses (hypoteni?) intersect is the center of the circle.

    Cheers,
    Joe
    Of course truth is stranger than fiction.
    Fiction has to make sense. - Mark Twain

Similar Threads

  1. Sanding the teeth Grrrrr
    By lonesomebob in forum CLOCKS
    Replies: 4
    Last Post: 24th March 2009, 10:15 PM
  2. advice needed on cutting an arc or circle
    By alwyn in forum WOODWORK - GENERAL
    Replies: 9
    Last Post: 17th March 2009, 08:22 AM
  3. How to find the best centre on an irregular lump?
    By rsser in forum WOODTURNING - GENERAL
    Replies: 23
    Last Post: 1st December 2008, 04:28 PM
  4. CA/BLO Haze - GRRRRR
    By Jiminidaho in forum WOODTURNING - PEN TURNING
    Replies: 11
    Last Post: 5th September 2007, 04:23 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •