Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 81
Thread: Bed, Double: Elevated - Rimu
-
19th February 2011, 03:20 PM #1
Bed, Double: Elevated - Rimu
My son is moving to Sydney to work and study but his room is fairly small. After a bit of discussion we've decided his bed needs to be about 1300mm off the ground and have a large storage area underneath so he can maximise space in the room.
Got the timber (Rimu) from Australian Fine Timbers yesterday morning and started dressing it yesterday. This morning I had to change all the blades in my thicknesser and jointer as the Jarrah from the bench has taken its toll on the edges.
Today I'll cut and glue up some legs and tomorrow do some cutting to length of the main sections. The bed base is a very simple box, nothing flash will be attempted.
-
19th February 2011 03:20 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
19th February 2011, 03:25 PM #2Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Mmmmmmmmmmmmm! Rimu. Nice>>
-
19th February 2011, 07:08 PM #3
-
19th February 2011, 11:25 PM #4
-
20th February 2011, 09:03 AM #5
Racking won't be a problem Groggy? Fair bit of weight on top with the frame, slats, matress and at least one body.
Those were the droids I was looking for.
https://autoblastgates.com.au
-
20th February 2011, 11:07 AM #6
-
20th February 2011, 11:51 AM #7GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
Great lot of rimu.
I've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
20th February 2011, 11:56 AM #8
A couple of diagonal braces between the rail and the frame should stiffen it up.
My daughters bed is similar and has a single brace in the back corner. Hers has solid ends so movement front to back is not a problem.Those were the droids I was looking for.
https://autoblastgates.com.au
-
20th February 2011, 12:00 PM #9Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
-
20th February 2011, 12:17 PM #10
Diagonal braces might be the go. Would they need to be at the front and the back, or just the back do you think?
-
20th February 2011, 04:28 PM #11
You should only need them at the back. You could even make them a bit fancy and make them a feature.
Morticed into the leg and underside of the frame. We all need M&T practise. Oh wait, you have a domino. That takes all the fun out.Those were the droids I was looking for.
https://autoblastgates.com.au
-
20th February 2011, 04:33 PM #12
Fancy? You mean straight
Thanks for the feedback, I'll give that some thought. I have to scarper off to Canberra for a few days so I'll think about it while I am gone.
I made the slats today, 18 of then with a 2mm rebate at each end and another in the middle. These will be screwed in place to help make the frame more rigid.
-
20th February 2011, 09:29 PM #13
Watch out for the weight. Having made numerous timber slat style beds, I know that if you have to move them it can be a big issue. Sons tend not to stay to long in one place.
Knock down or semi-knock down can assist when it comes to the dreaded move.
I am the worst offender for this so consider doing as I say not as I do. Our current bed needs approximately four strong men under the age of 30 to move it and the promise of beer to follow.
On the positive side, it doesn't bounce much.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
20th February 2011, 09:40 PM #14
It will be a knockdown job, a few screws to tighten things maybe. It has to go to Sydney in the ute so I reckon headboard, tailboard and the rest in bits.
-
20th February 2011, 10:14 PM #15
Hi Guys, the rail across the front could just be flat on the floor, like a spreader with the main braceing on the back and sides as you have already discussed above.
Similar Threads
-
An elevated fiddleback maple display cabinet.
By Woodwould in forum WOODWORK - GENERALReplies: 3Last Post: 22nd June 2008, 12:24 PM