Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 15
Thread: Fixing Twisted boards
-
29th October 2013, 06:25 PM #1ungifted amateur
- Join Date
- Sep 2008
- Location
- cliftonhill
- Posts
- 45
Fixing Twisted boards
About 3 months ago I purchased from Australian Furniture Timbers some Bolly Silkwood to make a desk. Total cost $600.... so far.
I ran the boards through my GMC thicknesser and joined 3 lengths to make a start on the top.
Then I went away for 3 months. On return the top had cupped badly as I had not reversed the grain every second board and one board had a split in one end.
So I cut free the worst cupped board and I can plane the 2 remaining back to flatness.
But all the remaining boards now have a slight twist in them. But little cupping.. go figure.
How can I fix this problem?
Surely someone else has solved this problem. I have a shed full of slightly twisted wood and I don't want to spend the rest of my life making small boxes.
-
29th October 2013 06:25 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
30th October 2013, 07:11 PM #2Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
If by 'fix' you mean 'un-twist', I don't believe it's possible. The only method I'm aware of is buzzing/planing one face flat and running it through a thicknesser.
Timber will keep moving, so only dress what you need, when you need it. Once you polish/seal your work it's pretty well behaved.
-
30th October 2013, 07:46 PM #3ungifted amateur
- Join Date
- Sep 2008
- Location
- cliftonhill
- Posts
- 45
Fixing Twisted boards
The thicknesser doesn't usually solve the problem unless you glue a wedge ( equal to the twist) to one side so that the board will sit flat on the bench (rather than rocking).
Then if you put it through a thicknesser the high parts on the other side will be gone and you can turn the board over and do it again to get a flat board.
The problem here is that if you have a 20mm board which when put on a flat bench has one corner 3mm off the bench and you go through the processs just described you will finish up with a 14mm board. I am thinking maybe it would be better to rip the boards in half then try the flattenning process and joining then together agin with less thickness loss. This will be a lot of work.
But surely there is another solution.
-
30th October 2013, 08:16 PM #4GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
I think one of the best solutions is to make a router sled with a wide planer bit, wedge the workpiece in position, and run the sled over the timber to make one side flat. Then flatten the other side through a thicknesser
regards,
Dengy
-
30th October 2013, 08:33 PM #5Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
-
30th October 2013, 08:35 PM #6ungifted amateur
- Join Date
- Sep 2008
- Location
- cliftonhill
- Posts
- 45
Fixing Twisted boards
Hey!!! very good!
I take it that you mean .. clamp one end of the board to a flat bench. Then have a router sled which rides on the bench and work on the raised corner of the board.
This is a much better solution than my original.
Any more out there?
-
30th October 2013, 08:54 PM #7
Having a thicknesser without a jointer is a time waster. Trying to do it with a router sled is just masochistic unless the board is really really wide.
If you want to save time and possibly money, get a scrub plane and some winding sticks. Hand plane one side roughly near to flat then run it through the thicknesser.
-
30th October 2013, 09:50 PM #8Sometimes in the daily challenges that life gives us, we miss what is really important...
-
30th October 2013, 10:20 PM #9
My name is Fuzzie and I am a masochist.
On long boards I find it a whole lot easier to take the high corners off a twisted board with a scrub plane that trying to do it all on the jointer. Perhaps if I had commercial grade machinery that wouldn't be the case, but with my gear I think it is not only quicker but safer.
-
31st October 2013, 10:43 AM #10ungifted amateur
- Join Date
- Sep 2008
- Location
- cliftonhill
- Posts
- 45
Fixing Twisted boards
Thanks to all for the contrubution. Unfortunately I don't have room for a jointer as I am essentially working in a car port with a big cupboard attached.
So I might need to look at a scrub plane and make a sled for the router.
-
31st October 2013, 05:06 PM #11
A scrub plane will straighten your boards in very little time. Maybe an hour for the top. Then thickness the other side. And reglue to make whole again.
I am learning, slowley.
-
4th November 2013, 05:55 PM #12ungifted amateur
- Join Date
- Sep 2008
- Location
- cliftonhill
- Posts
- 45
Fixing Twisted boards
It turned out that there was another solution.
I have wetted down some boards then put a wedge under one corner to apply opposite twist and clamped the board to the bench for 24 hours.
Hey presto board is now not twisted.
-
4th November 2013, 06:14 PM #13Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
Nice one I'm curious to see if they stay flat once they fully re-dry.
Just remember that your timber has a relatively low density and that trick won't always work, especially with thicker stock and/or dense hardwoods.
-
4th November 2013, 06:30 PM #14ungifted amateur
- Join Date
- Sep 2008
- Location
- cliftonhill
- Posts
- 45
Fixing Twisted boards
Time will tell. I will fix these boards together asap and let you know if things don't turn out.
-
4th November 2013, 09:38 PM #15
Just to add to what has already been said. We are having a very dry spell with prolonged low humidity following quite a few rather wet years so wood in general is acting badly. Even boards that were well seasoned are on the move. Time to apply all the good wood handeling practices.
Regards
John
Similar Threads
-
Twisted box
By AlexS in forum BOX MAKINGReplies: 9Last Post: 25th December 2012, 08:06 AM -
A bit twisted
By gawdelpus in forum WOODTURNING - PEN TURNINGReplies: 7Last Post: 30th January 2010, 11:15 PM -
Fixing twisted rails when milling.
By BobL in forum SMALL TIMBER MILLINGReplies: 7Last Post: 14th July 2008, 11:17 AM -
Twisted saw
By Frank&Earnest in forum BANDSAWSReplies: 18Last Post: 14th May 2008, 12:24 PM -
Twisted jokes 3
By simon c in forum WOODIES JOKESReplies: 6Last Post: 5th May 2005, 01:42 PM