Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Stabilising knots
-
16th November 2018, 11:36 PM #1SENIOR MEMBER
- Join Date
- Mar 2018
- Location
- Sydney
- Posts
- 469
Stabilising knots
I'm creeping along in my work bench build (Moravian style bench), but have made a rookie mistake (as i am a rookie after all) of not planning the layout properly.
In the first cross beam between the two legs I've got a knot right where a mortice will be to allow for a wedge to hold it together.
I've seen on youtube people stabilising knots using west system epoxy, but are there other alternatives to save me buying some just for this? Would wood filler, or regular food glue work?
Any advice would be most helpful.
I've attached a 2nd photo showing a similar bench to illustrate the wedge placement.
-
16th November 2018 11:36 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
16th November 2018, 11:57 PM #2
Nice Work
I think Ca glue or even some epoxy can be used for stabalising knots look into this a bit deeper with a few searchers though memory is a bit rusty on this one
heres a starter
https://sawmillcreek.org/showthread....and-Wood-Knots
Regards LouJust Do The Best You Can With What You HAve At The Time
-
17th November 2018, 02:00 PM #3
runny super glue (cyanoacrylate). Not sure about Australia, but in Canada I can get super glue in 3 viscosities, "runny" as water, like thin syrup or like thick honey
regards from Alberta, Canada
ian
-
17th November 2018, 06:19 PM #4
The problem with knots is that they tend to shrink more than the surrounding timber...and then fall out. The glue should prevent the latter but won't prevent the former. This could particularly be the case with so called kiln dried timber, such as radiata pine.
-
17th November 2018, 06:57 PM #5
But if the OP is using really sharp tools and takes their time, they should be able to cut their wedge mortise through a stabilised (or glued in) knot, which if it falls out later won't really matter, or can be repaired with a dutch man.
It might even pay to cut the knot out now and do a dutch man repair.regards from Alberta, Canada
ian
-
17th November 2018, 07:25 PM #6SENIOR MEMBER
- Join Date
- Mar 2018
- Location
- Sydney
- Posts
- 469
Thanks all,
I'm definitely taking my time, mostly through having to keep the noise down so not to annoy the neighbours!
To make the mortices I'm clearing much of the waste using a brace then chiseling the rest. I'm taking my chisels up to 8k grit, then honing a bit on a strop so should be sharp enough.
As this is only my first workbench, and largely a exercise in joinery, it's not need to last forever though and as the bench dismantles any piece can be easily replaced.
I've never heard of a Dutch man so I've a bit of research to do.
Thanks everyone.
-
17th November 2018, 08:05 PM #7
what is a dutchman?
see here https://en.wikipedia.org/wiki/Dutchman_(repair)
and here https://makezine.com/projects/dutchman-wood-repair/regards from Alberta, Canada
ian
-
17th November 2018, 10:25 PM #8
-
18th November 2018, 12:06 AM #9SENIOR MEMBER
- Join Date
- Jul 2014
- Location
- Brisbane
- Posts
- 937
If you only want a small quantity of epoxy for this job, Boatcraft do a sample Bote Cote pack. It's a really easy to use epoxy and for $15 you can't go too far wrong at all.
-
19th November 2018, 06:00 PM #10Senior Member
- Join Date
- Apr 2017
- Location
- Dandenong Ranges
- Posts
- 266
You could cut it out and glue another bit in - I assume that's a Dutchman.
You could make the wedges horizontal instead of vertical and not have to cut into the knot at all. Look better anyway in my opinion.
Similar Threads
-
Downhill at 38 knots
By Chris Parks in forum MISC BOAT RELATED STUFFReplies: 6Last Post: 25th June 2021, 05:43 PM -
Nautical knots??
By JTTHECLOCKMAN in forum WOODTURNING - PEN TURNINGReplies: 10Last Post: 28th August 2014, 10:21 PM -
A Couple of Knots
By MBUMIK in forum WOODTURNING - PEN TURNINGReplies: 11Last Post: 16th May 2013, 12:37 AM -
Knots
By Tim Preston in forum NON WOODWORKReplies: 3Last Post: 2nd November 2010, 12:43 AM