Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 26 of 26
Thread: Router cabinet/table WIP
-
4th March 2013, 10:30 AM #16
Congrats LPlates, this has come together real nice!. i think im going to be moving from my Triton router table and mount my TRA001 with a woodpecker plate into a cabinet i have similar size to yours. This thread has inspired me to do so.
How did you setup the jig to cut out your moritse for the joins? Draws look great also. I have purchased a few from that ebay link so thanks again!
Going to look great with a t-track and fence installed
-
4th March 2013 10:30 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
5th March 2013, 08:26 AM #17Frequent Learner
- Join Date
- Aug 2012
- Location
- Geelong
- Posts
- 181
router fitting
As promised i got back to the project last night and made some small advancements. I cut down the table so that the length is right now and i fitted the hinges to it so that i can open it easily without having to bend over at and awkward angle to get at the router, actually it's kinda half fitted since i still need to recess the hinges a bit deeper so that the table fits flush, but it's a start.
Most of my time however was spent crafting some hold down plates to hold the router in place. I cut up a piece of angle iron i had laying around with a grinder and then drilled the holes for the recycled bolt knobs i had. The result is shown below. I also painted the pieces black and then glued some rubber from a bicycle tube to the underside so that they don't scratch the router when fitted.
IMG_20130304_180309.jpgIMG_20130304_180921.jpg
As you can see i also numbered each set of holddown/knob since they all fit slightly differently, some of the bolt threads are longer. Should make things simpler when it comes to use.
-
5th March 2013, 08:32 AM #18Frequent Learner
- Join Date
- Aug 2012
- Location
- Geelong
- Posts
- 181
Thanks Delbs,
I cut the mortises using my new router and a jig i screwed together from offcuts i had laying about gathering dust. There are pictures of it in the first post on this thread (pic 4 and 5). Basically it was just a fence that I temporarily mounted to the piece using clamps. It was a little awkward but it worked well enough. Probably need to get a bit more creative if you are using hardwood or something of better quality. Given my cheap materials i wasn't afraid to make a mistake.
Good luck with your build and please post a WIP with photos if you can. We all love to see builds come together.
Cheers
Mat
-
7th March 2013, 08:25 AM #19Frequent Learner
- Join Date
- Aug 2012
- Location
- Geelong
- Posts
- 181
just the top to go
So after a couple of days of fiddling with the remaining little things i've almost got the cabinet finished. Just need to finish the top now which will require some shopping since the alloy U channel that i have laying around isn't long enough and bunnies does not sell decent stuff, may need to go to an aluminium specialist (or carbatec via mail...too $$$). Also need to find where i can get some laminex sheet.
Anyway, last night i fitted the covers for the tops of the drawers so that i don't get dust into them from above and I fitted a stop to the table top so that i can lift it and leave it standing without hands on. Couldn't resist fitting the router either just to see how it looks. Not sure if i will have enough protrusion of the bit though, it's sticking out about 20mm which should be find for most things, i can always remove the plastic plate on the router base to get an extra 5mm or if it proves to be an issue more often than not i can always put in a proper router baseplate. Time will tell. I still have to make a bigger hole for the bits to protrude too but I only had a 3/4 forstner bit so that will have to come later too.
IMG_20130306_182306.jpgIMG_20130306_182317.jpgIMG_20130306_190907.jpgIMG_20130306_190934.jpgIMG_20130306_190944.jpg
Cheers
Mat
-
7th March 2013, 08:48 AM #20
Looking good.
Can you imagine what I would do if I could do all I can? -- Sun Tzu
-
7th March 2013, 09:16 AM #21
I know after you start working with it you may find that you modify it slightly.
-
7th March 2013, 01:19 PM #22
It's coming together very nicely Mat.
Does your collet fit through the 3/4" hole for tightening or loosening it?
When I made my table I managed to get an offcut of 10mm polycarbonate sheet to recess into the table. I removed the plastic plate off the router base and then screwed the base directly to the sheet. I only have one size hole through the sheet and no adaptor rings, but that hasn't been a problem for me yet as most of my bits are not overly large. This setup gives me plenty of height of the bits.
-
9th March 2013, 09:55 PM #23
Well Done L Plates, looking really good.
Not sure of your plans, but a 100mm dust port in the back at the bottom of your cupboard, & a door on the front would work well.
Or if you want to get creative, build a false back into it with a sloping sheet from the front of the bottom of the router. That would give you extra cupboard space as well, if you need it. You may not believe it, but that description is really clear in my head.
Once you have your router table finished, another alternitive to drawer joinery is a Lock Mitre Joint. The lock mitre bit can be a bit of a mongrel to set up, but it makes a lovely joint. can also be used for 180 degree joints as well as 90 degree
SteveThe fact remains, that 97% of all statistics are made up, yet 87% of the population think they are real.
-
9th March 2013, 11:21 PM #24Intermediate Member
- Join Date
- Sep 2010
- Location
- Melbourne
- Posts
- 48
-
15th April 2013, 09:46 AM #25Frequent Learner
- Join Date
- Aug 2012
- Location
- Geelong
- Posts
- 181
finally finished...almost
So it's been a while since i opened this post. I lost heart with the project after a series of mistakes and another project for my brother took me away from it for a while but I had enough of looking at the failed table top and decided it was time to start again.
So to keep it short the stuff up was with the gluing of the formica/laminex to the MDF top. I had a brain fade and decided to use standard PVA glue to put it all together, which probably would have been fine if I clamped it all nicely. I thought i had done a reasonable job of clamping it all down but there were gaps and of course all the glue that was pushed out from the clamped parts accumulated there, resulting in waves in the final surface. Here are some shots of the stuffed up attempt. (note that i used the older and smaller router table to clamp the new one....hence the problems with pockets of squeezeout).
IMG_20130407_084749.jpgIMG_20130407_084735.jpgIMG_20130407_084810.jpgIMG_20130407_090146.jpg
So i basically had to scrap the whole failed top and start again, hence the delays. The second time around i did some research and realised that the glue to use was contact adhesive....messy stuff but much better in this sort of application where clamping is difficult. I also got myself some miter track from McJing and fitted that. The failed top was recycled and used to make the fence as seen in the pictures below. I also took the opportunity to address some shortcoming i saw in the original attempt. I used plywood for the topmost part so that the router could be closer to the surface but still be secure. I changed the location of the hinges so that i could flip the whole table over to make mounting the router easier.
I also managed to make another stuff up. I really need to be more careful when i do stuff after work. I make some really dumb mistakes when i'm forging ahead all excited and half dead. This time i drilled a hole for the "above table height adjustment" that the Triton routers use, which was fine in theory. I located at the front of the table so i could adjust the height without moving the fence if needed. Problem was that i didn't take into account the position of the clamps that hold the router in place whcih were now 90degrees from their optimal position. I spent an hour or so rethinking how to redo the hold down clamps to suit but decided in the end that it was best to drop the problematic hole and use the clamps in their original position since they work best. Now i have an extra hole on the top without purpose...doh!
Overall i'm pretty happy with the outcome but i think i'll wait to redo the hole for the height adjust and see how much i would actually use it first. Anyone have an idea how to nicely fill a hole in the laminex?
IMG_20130414_092808.jpgIMG_20130414_112142.jpgIMG_20130414_112153.jpgIMG_20130414_114538.jpg
The pics are pretty self explanatory. IN the first one i am using a piece of 3/4 pine as a leg that wedges into the mitre track and holds the table in place while i fiddle with the clamps. The final picture is of my bit holder which i made from a piece of blackwood cutoff from another project, makes things a lot neater.
Cheers
Mat
-
17th April 2013, 10:38 PM #26
Router cabinet/table WIP
Hey Mat
Been following this one for a while,good job on the new top with the t-track and fence.
I also was considering using the above table height adjustment for the triton but when I looked into it I realised that my TRA001 that lives mounted in my table doesn't even have the height adjustment to use the above table winder, The amount of time it takes me to just wind the TRA under the table is fine with me. The winder is suited to my MOF001 but that's my hand held and I don't want it mounted lol. So I just use the rest of the accessories in TGA150 kit
As for plugging the hole in the top if you don't mind looking at it I have filled it with a glued up dowel (depends on size of your hole) and used a flush cutting japanese saw to make it flat. Yep you can see it but I don't care as its just the top of my router table its covered in dust most of the time anyway.
I've used your table and draws for some inspiration. Like the fold out table at the back too
Similar Threads
-
Confused router bit cabinet
By peteandoreen1 in forum WOODWORK PICSReplies: 7Last Post: 12th December 2009, 09:35 AM -
Triton Router table RTA300 VS Carba-Tec Cast Iron Top Router Table
By pellcorp in forum TRITON / GMCReplies: 17Last Post: 30th April 2009, 02:43 PM -
Yet another router table cabinet
By Barrie Restall in forum ROUTING FORUMReplies: 13Last Post: 30th August 2006, 10:46 AM