Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Tool identification
-
16th January 2017, 10:25 PM #1New Member
- Join Date
- Jan 2017
- Location
- Goonellabah Australia
- Posts
- 3
Tool identification
Hi guy's I've been looking at router plates and came across this one. I would appreciate thoughts please and what is the tool that fits into the rectangular hole ? ..... 235*120*8mm Aluminum Router Table Insert Plate w/ 4 Insert Rings DIY Woodworking | eBay router fun ny thing.jpgrouter funny 1.jpg
-
16th January 2017 10:25 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th January 2017, 07:56 AM #2GOLD MEMBER
- Join Date
- Aug 2012
- Location
- Imbil
- Posts
- 1,167
Hi,
The attachment that is in the rectangular hole is a guide roller from a Makita trimmer/router,it may be that the trimmer is what is attached as the router under the plate and the rectangular hole is to allow for it to mount on the trimmer in it's original mount which is on the side of the body of the trimmer.
Regards Rod.Rod Gilbert.
-
17th January 2017, 08:24 PM #3
You haven't mentioned whether you have a router or not at the moment. But beware that the plate you have linked is basically only suitable for trim router units as it is way to narrow at 120mmW to accept a medium or large router as the base on the routers would be wider than the plate.
Most trim routers are fairly low powered (in router terms) with a power range of 450-900W, and they are generally very fiddly to accurately set the bit height if mounted inverted in a table. Typically they use small diameter bits, lacking the power to operate bits larger than 12.7mm (1/2in) effectively. They are also limited to either 6 or 6.35mm (1/4in) shank bits.
If you already have a trim router and are merely seeking to extend it's versatility and are aware of these limitations, thats fine. However if you are planning to buy a router larger than a basic trimmer, and hoping to use this plate as a cheap way of getting it into table, I think the plate size will be against you. In that case, I would suggest that you set up a table without a plate initially, and add a more suitable plate at a later time when funds permit.I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
18th January 2017, 01:06 PM #4New Member
- Join Date
- Jan 2017
- Location
- Goonellabah Australia
- Posts
- 3
Thanks guy's for your helpful info .I just purchased may first router (Ryobi 1600W Plunge Router)
and the first job with it will be to build a bench .This is the router https://www.bunnings.com.au/ryobi-16...outer_p6210608 What plate would you recommend?
-
18th January 2017, 01:07 PM #5New Member
- Join Date
- Jan 2017
- Location
- Goonellabah Australia
- Posts
- 3
Many thanks Rod
-
18th January 2017, 02:05 PM #6GOLD MEMBER
- Join Date
- May 2013
- Location
- Rockhampton QLD
- Age
- 68
- Posts
- 2,343
Welcome to the forum Jonny.
Ross
Similar Threads
-
Tool Identification
By Ando967 in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 21st December 2016, 09:42 PM -
Tool identification
By ozhunter in forum HAND TOOLS - UNPOWEREDReplies: 17Last Post: 17th July 2012, 04:55 PM -
Tool Identification?
By Conrad85 in forum HAND TOOLS - POWEREDReplies: 4Last Post: 24th March 2012, 01:07 PM -
Hand tool identification help needed
By doyle007 in forum HAND TOOLS - UNPOWEREDReplies: 1Last Post: 28th November 2006, 07:10 AM